How to disassemble the valve core of the kitchen faucet

Method 1: Close the main water valve first, and then put it.

There is a red and blue mark of about 8 mm on the faucet handle, buckle it down, loosen the fixing screw counterclockwise with a flathead screwdriver, take off the handle, use a live wrench to disassemble the valve core of the faucet, use a wrench to open the upper part of the gland, and take out the ceramic valve core inside.

Method 2: Close the main water valve first, you can use a screwdriver to insert it under the handle of the faucet, pry it up left and right, pry it on one side, take it slowly, and the force is even and stable, so that you can remove the valve core.

Method 3: Close the main water valve first, unscrew the blue cover on the right handle, loosen the screws inside with a Phillips screwdriver, take off the handle, and the valve core will be exposed, and then use a movable wrench to unscrew the valve core.

1.Turn off the water source: The water source must be turned off before the faucet valve is removed to avoid damage to the water flow or waste of water.

2.Remove the faucet handle: Use a screwdriver or wrench to remove the faucet handle, usually there will be a screw or buckle under the handle, and the valve core can be seen after disassembly.

3.Disassembling the spool: Use a wrench or wrench barrel to remove the spool, usually there will be a nut or buckle leaking above the spool, and the spool can be removed after disassembly.

4.Clean the spool: Put the spool in clean water and wipe it with a brush or cloth to remove dirt and sediment on the surface of the spool.

5.Replace the spool: If the spool is damaged or cannot be repaired, you will need to replace the spool with a new one, install the new spool in its original position, and reinstall the handle.

6.Test the faucet: turn on the water source again, test whether the faucet is working normally, if there is a leak or other problems, you need to re-check and adjust.

Notes:1Before disassembling the faucet spool, the water source must be turned off to avoid damage or waste of water due to the flow of water.

2.When disassembling the spool, be careful not to damage the surface of the spool, so as not to affect the use effect. 3.

When replacing the spool, choose the same model as the original spool to ensure compatibility and stability. 4.When testing the faucet, pay attention to whether the water flow is normal and whether there are any leaks or other problems.

How do you dismantle a kitchen faucet? You can easily replace the kitchen faucet by yourself.

Method copy one:

Close the main water valve first, and then put a red and blue mark of about 8 mm on the faucet handle.

Method 2: Close the main water valve first, you can use a screwdriver to insert under the handle of the faucet, pry left and right, pry it on the side, take it slowly, and the force is even and stable, so that you can remove the valve core.

Method 3: Close the main water valve first, unscrew the blue cover on the right handle, loosen the screws inside with a Phillips screwdriver, take off the handle, and the valve core will be exposed, and then use a movable wrench to unscrew the valve core.

First close the main water valve in the kitchen, then put the faucet handle with a red and blue mark of about 8 mm, buckle it down, loosen the fixing screw counterclockwise with a flathead screwdriver, take off the handle, use a live wrench to disassemble the faucet and replace it, and install it according to the original appearance.

Look underneath the handle, there's a small lid, open. There are screws inside, and the handle can be removed by twisting it. After removing the handle, use a large wrench to unscrew a nut and the spool can be removed.

After removing the wrench, there must be a four-sided or six-sided nut that can be screwed with a wrench.

Method 1: Close the main water valve first, and then put the faucet handle bai hand has a red and blue mark of about 8 mm, buckle the dao, loosen the fixing screw counterclockwise with a flathead screwdriver, take off the handle, use a live wrench to disassemble the valve core of the faucet, use a wrench to open the upper part of the gland, and take out the ceramic valve core inside.

Method 2: Close the main water valve first, you can use a screwdriver to insert it under the handle of the faucet, pry it up left and right, pry it on one side, take it slowly, and the force is even and stable, so that you can remove the valve core.

Method 3: Close the main water valve first, unscrew the blue cover on the right handle, loosen the screws inside with a Phillips screwdriver, take off the handle, and the valve core will be exposed, and then use a movable wrench to unscrew the valve core.

Unscrew the gland with a wrench, the valve core will come down, if you don't know what the gland is, search on Taobao, there are ways to install and disassemble the gland and valve core.