When will the newly installed toilet be ready for use

The first step in toilet installation.

Examine. For the toilet, in order to maintain a good use effect, then the toilet installation environment needs to be reasonable and suitable. Therefore, it is necessary to keep the ground flat and the sewage pipe unblocked before installation.

For the ground, the main thing is to check whether the toilet is horizontal, whether the ground around the toilet installation position is on a horizontal line, if the ground is not flat, then the ground leveling process should be carried out. For pipelines, it is necessary to pay attention to whether there is a blockage in the sewage pipeline and whether the sewage discharge is smooth.

The second step of toilet installation.

When installing the toilet, it is necessary to pay attention to the docking of the sewage pipe of the toilet bowl and the ground sewage pipe, and keep the connection between the pipes tight, generally draw a cross center line at the sewage outlet at the bottom of the toilet bowl to ensure that the center of the sewage outlet and the center line of the sewage pipe will correspond, and then place the toilet horizontally on the ground, seal the sealing ring, and then install and fasten the screws and decorative caps on the ground.

The third step of toilet installation.

After installing the toilet bowl horizontally on the ground, we need to carry out the sealing work on the bottom of the toilet, mainly the sealing of the sewage outlet. Generally, special sealing tools are used: sealing rings or glass glue to seal the bottom.

The cement and sand are adjusted according to the ratio of 1:3, and the bottom of the toilet is painted, and the sealing work is carried out, and the balance between the left and right sides of the bottom should be paid attention to when applying cement paint.

Toilet installation step 4.

After installing the bottom and body of the toilet, we need to install accessories such as the water tank. The water tank is the key to whether the toilet is leaking, so you must pay special attention to the unblocking and sealing performance of the water tank when installing. During the installation, whether the water tank is unobstructed can be tested by draining the water, draining the water for 3 minutes to rinse, cleaning the pipe, and then installing the angle valve and connecting hose.

When installing the hose, it is necessary to ensure that the water tank and other accessories can be connected to the water valve after installation, so that it can be kept unobstructed when in use, and there will be no water leakage.

Toilet installation step 5.

When the installation process reaches the fifth step, that is, when the toilet installation is roughly completed, but we need to ensure the normal use of the toilet, so we must carry out the inspection and acceptance work. During the inspection, it is necessary to pay attention to whether the water inlet of the water valve is smooth, whether there is a leak in the water tank, and whether the flushing process is smooth.

After two hours, you can pour water If you sit, at least 10 hours, it depends on whether the ground is flat, whether there is a warped place, whether the ventilation is good, and what glue is scored, the above can reach 10 hours, but you must sit steadily, you can't shake, if it is a neutral glue, it will dry slowly, 24 hours, and a good quick-drying acidic glue will dry quickly.

In winter, when it's cold, it takes two or three days to use, and when it's hot, one day is fine....The main reason is that the flush will damage the solidification of the glass glue....

Normally, it should be installed in the bathroom ceiling and only after the paint is finished.

Installation points. 1. Check the levelness of the ground where the toilet is to be installed, if it is found to be tilted, it can only be installed after adjusting to the level;

2. Check the sewage pipe of the toilet before installation, and clear the sediment, waste paper and other sundries in the sewage pipe;

3. The height of the drain is 2-5 mm above the ground;

4. After debugging and installing the water tank accessories, connect the tap water, fill the water tank into the water tank, and then observe whether the water tank or water inlet hose is leaking for a few minutes;

5. The water pressure of tap water is generally relatively stable, and the water tank is filled with water. Test the drain effect of the toilet bowl and whether the flush is strong. If the water vortex is fast and rushes quickly, it means that the water is unobstructed, and conversely, check for blockages.

After installation, it is ready to use after 24 hours.

Installation. It doesn't leak, and it can be used in 1-2 hours.

At least 3 days, otherwise it will be uneven if you don't do it!