Introduction to the steps of kitchen wall waterproofing practices

The decoration must be waterproofed, especially the walls of the bathroom, kitchen and balcony. These three areas use water every day, so they must be waterproof. How about kitchen wall waterproofing? Let's take a look at the kitchen wall waterproofing practice construction steps.

In the kitchen waterproofing, it is necessary to prepare tools such as brushes, rollers, electric mixers, nets of nonwoven fabrics or fiberglass, and also to prepare waterproof coatings. It depends on your choice. Usually, you have to choose between two types. coatings, the second is special waterproof wall coatings.

Kitchen wall waterproofing practice step 2,

In general, the soil is irregular, so it is necessary to repair the bottom of the kitchen before waterproofing, especially in the front area of the yin-yang forest. More attention is paid to non-standardization. A shovel can be used to scoop up raised slag and debris.

The depressed area must be repaired and smoothed. If there is a crack or water leak, it is necessary to repair it.

Step 3 of the waterproofing method of the kitchen wall and the surface of the house, clean the base surface.

Once the ground has been repaired, it is also essential to ensure that the surface of the base is free of dust, particles, and debris. Therefore, it can be washed with water before construction. When the surface is wet, there should be no clear water.

Step 4 of the kitchen wall waterproofing method, mix the waterproof slurry.

The first thing to do is to make the floor waterproof, so adjust the waterproof floor first. Pour an impermeable coating on the plastic bucket in a certain proportion, the first pour latex paint, then pour dust in the dust, shake well with two agitators, and let stand without particles for three minutes.

Step 5 of the kitchen wall waterproofing practice, brush the soil waterproof paste.

At this point, you can start using waterproof sludge. First of all, you have to apply a small area of special brushing in some special areas, especially floor drains, pipes and corners around the walls. The area can then be painted for the first time in a large area.

Once the brush is wet, apply paint and brush in one direction. The thickness of the coating film is less than 1mm, which is easy to dry and is not prone to bubbles and cracks. After drying, you can use the cross in the direction of the cross to brush a second time to prevent leakage, and the day can be tested for water blockage.

Step 6 of the kitchen wall waterproofing method, apply the waterproof paste wall.

The kitchen space is also waterproofed on the wall. It has a height of about 180 centimeters and prevents the faucet from wetting the walls with water. The practice is consistent with the soil waterproofing method. The only difference is that the waterproofing mixture is different, and a specific paint for the walls must be used.

Editor's summary:

The kitchen wall waterproofing manufacturing method Step 1

In the kitchen waterproofing, it is necessary to prepare tools such as brushes, rollers, electric mixers, nets of nonwoven fabrics or fiberglass, and also to prepare waterproof coatings. It depends on your choice. Usually, you have to choose between two types. coatings, the second is special waterproof wall coatings.

The kitchen wall waterproofing manufacturing method Step 2

In general, the soil is irregular, so the bottom of the kitchen must be repaired before waterproofing, especially in the yin-yang area. More attention is paid to non-standardization. A shovel can be used to scoop up raised slag and debris.

The depressed area must be repaired and smoothed. If there is a crack or water leak, it is necessary to repair it.

The kitchen wall waterproofing manufacturing method Step 3: Clean the base surface.

Once the ground has been repaired, it is also essential to ensure that the surface of the base is free of dust, particles, and debris. Therefore, it can be washed with water before construction. When the surface is wet, there should be no clear water.

The kitchen wall waterproofing manufacturing method Step 4: Mix the waterproof slurry.

The first thing to do is to make the floor waterproof, so adjust the waterproof floor first. Pour an impermeable coating on the plastic bucket in a certain proportion, the first pour latex paint, then pour dust in the dust, shake well with two agitators, and let stand without particles for three minutes.

The kitchen wall waterproofing manufacturing method Step 5, brush the soil waterproof paste.

At this point, you can start using waterproof sludge. First of all, you have to apply a small area of special brushing in some special areas, especially floor drains, pipes and corners around the walls. The area can then be painted for the first time in a large area.

Once the brush is wet, apply paint and brush in one direction. The thickness of the coating film is less than 1mm, which is easy to dry and is not prone to bubbles and cracks. After drying, you can use the cross in the direction of the cross to brush a second time to prevent leakage, and the day can be tested for water blockage.

The kitchen wall waterproofing manufacturing method Step 6: Apply waterproof paste wall.

The kitchen space is also waterproofed on the wall. It has a height of about 180 centimeters and prevents the faucet from wetting the walls with water. The practice is consistent with the soil waterproofing method. The only difference is that the waterproofing mixture is different, and a specific paint for the walls must be used.

1. Prepare tools and raw materials, prepare brushes, rollers, electric mixers, non-woven fabrics or glass fiber mesh and other tools for kitchen waterproofing, and prepare waterproof coatings, which depends on your choice, generally choose two kinds, one is a special waterproof coating for the ground, and the other is a special waterproof coating for the wall.

2. The base surface is repaired, and the general ground is uneven, so the kitchen base surface should be repaired before doing waterproofing, especially in the yin and yang corner areas, and the unevenness should be leveled. You can use a shovel to shovel off the raised cement slag and debris, and the recessed places should be repaired and smoothed, and cracks or water seepage also need to be plugged and repaired.

3. The base surface is clean, after the ground is repaired, it is necessary to ensure that the base surface is free of any dust, particles and garbage, etc., so you can use water to clean it before construction, as long as the surface is moistened, and there can be no open water.

4. Mix the waterproof slurry and do the waterproofing of the ground first, so the waterproof coating on the ground is mixed first. Pour the waterproof paint into the plastic bucket according to a certain proportion, pour the paint emulsion first, then pour the powder, stir the two evenly with a stirrer, and let it stand for three minutes after it is in a particle-free state, and it can be used after eliminating small bubbles.

5. Ground waterproof slurry brushing, at this time you can start to paint waterproof slurry, first of all, some special areas should be brushed in a small area, especially floor drains, around the pipe, and at the corners of the wall. Then other areas can be painted in a large area for the first time, the brush is soaked and the paint is adhered to, brushed in one direction, and the thickness of the coating film is within 1mm, which is easy to dry, and is not easy to bubble and crack. After drying, you can apply the second pass with a cross staggered direction to avoid missing brushing, and you can perform a closed water test the next day.

6. The wall waterproof slurry is painted, and the kitchen space should also be waterproof measures for the wall, the height of which is about 180cm, which can prevent the faucet from soaking the wall with water, and its practice is consistent with the ground waterproof practice, the only difference is that the waterproof slurry is different, and the wall special paint should be used.

The decoration must be waterproofed, especially the waterproofing of the walls of the bathroom, kitchen and balcony. These three areas use water every day, so they must be waterproof. How about kitchen wall waterproofing?

Construction steps.

The kitchen wall waterproofing manufacturing method Step 1

In the kitchen waterproofing, it is necessary to prepare tools such as brushes, rollers, electric mixers, nets of nonwoven fabrics or fiberglass, and also to prepare waterproof coatings. It depends on your choice. Usually, you have to choose between two types. coatings, the second is special waterproof wall coatings.

The kitchen wall waterproofing manufacturing method Step 2

In general, the soil is irregular, so the bottom of the kitchen must be repaired before waterproofing, especially in the yin-yang area. More attention is paid to non-standardization. A shovel can be used to scoop up raised slag and debris.

The depressed area must be repaired and smoothed. If there is a crack or water leak, it is necessary to repair it.

The kitchen wall waterproofing manufacturing method Step 3: Clean the base surface.

Once the ground has been repaired, it is also essential to ensure that the surface of the base is free of dust, particles, and debris. Therefore, it can be washed with water before construction. When the surface is wet, there should be no clear water.

The kitchen wall waterproofing manufacturing method Step 4: Mix the waterproof slurry.

The first thing to do is to make the floor waterproof, so adjust the waterproof floor first. In a certain proportion of the plastic barrel is poured with a non-permeable ear of the coating, the first pour the emulsion paint, then pour the dust in the dust, shake well with two agitators, and let stand without particles for three minutes.

The kitchen wall waterproofing manufacturing method Step 5, brush the soil waterproof paste.

At this point, you can start using waterproof sludge. First of all, you have to apply a small area of special brushing in some special areas, especially floor drains, pipes and corners around the walls. The area can then be painted for the first time in a large area.

Once the brush is wet, apply paint and brush in one direction. The thickness of the coating film is less than 1mm, which is easy to dry and is not prone to bubbles and cracks. After drying, you can use a mill brush across the direction of the cross for a second time to prevent leakage, and the day can be tested for water blockage.

The kitchen wall waterproofing manufacturing method Step 6: Apply waterproof paste wall.

The kitchen space is also waterproofed on the wall. It has a height of about 180 centimeters and prevents the faucet from wetting the walls with water. The practice is consistent with the soil waterproofing method. The only difference is that the waterproofing mixture is different, and a specific paint for the walls must be used.

Editor's summary: The above isThe kitchen wall waterproofing manufacturing method

You can get it for free