What should I do if the kitchen tile joint leaks?

But now, the Swiss Sika company has produced a transparent waterproof treatment agent, which was originally used for exterior walls, using the principle of permeation sealing to control the leakage of external walls, because it is transparent and penetrates the wall surface (does not produce a membrane that can be peeled), so it does not change the appearance of the original base surface. Based on this feature, we use it for the kitchen and bathroom to fill the leak, the effect is very good, and the workmanship is extremely convenient, rolling, brushing, spraying can be, 2 hours to finish two bathrooms and one kitchen is no problem!

Two points to add: 1. The effect is good if the tile is pasted with seams. The minimum seam width should be greater than 3mm, preferably 5mm. For seamless pasting, the effect is not guaranteed.

2. If there are obvious cracks, this scheme cannot be used alone. It is recommended to use Sika's Sikaflex one-component polyurethane adhesive sealant for sealing first.

If the floor is low, this is a more common phenomenon, more ventilation, and dry it in time when there is water.

Porcelain seam treasure: it is mainly made of high-tech polymer plus high-grade pigments and special additives, rich in color, bright in color, and with gold, silver, pearlescent, stainless steel color, suitable for matching with various color tiles; The whiteness of white is about 95%, the surface strength is high, hard as porcelain, and the apple tree kitchen and bathroom porcelain seam treasure; Its surface is smooth, smooth as porcelain, easy to scrub, dirty and clean, easy to clean, waterproof and moisture-proof, oil-proof, acid-resistant and alkali-resistant, avoid sanitary dead ends, can often maintain the original color, and will not pollute the tile during construction.

You have to find someone to fix it, otherwise it will become more and more leaky.

Let's pry the tiles!! You won't be able to make up for it for long if you don't show it! Water is pervasive!

Is it the ground floor? Did you do waterproof and moisture-proof before?

Toilet leakage can generally be divided into three situations: waterproof layer damage, drain pipe leakage, and water supply pipe leakage

1. Judgment of waterproof layer damage: plug the floor drain, and then release water on the ground, pay attention to observe the water leakage downstairs after 30 or 40 minutes, if the water leakage downstairs is serious, it is determined that the waterproof layer is leaking.

Treatment: Use Anju water without leakage. Through the penetration of a water carrier, a permanent waterproofing layer is formed below the tile surface.

2. Judgment of drain pipe leakage: drain to the floor, fill the hand basin, and flush the toilet repeatedly to see if the leakage downstairs is aggravated.

Solution: Replace the sewer pipe, try to plane as few bricks as possible, and finally need to redo the waterproofing on the ground.

3. Judgment of water supply pipe leakage: If the water leakage is uniform and continuous, turn off the upper water, and the water will be reduced and will not leak.

Solution: Replace the water pipe.

Tools Raw materials.

Water does not leak plastic buckets, brooms, rags, tool knives, and shovels.

Method steps.

1. Clean the bathroom floor.

2. Use a tool knife to cut the tile joint.

3. Use a rag to block all the floor drains in the bathroom. Note: If it is squatting, use gypsum powder and water to adjust it into a dry mud shape, and surround a 3 cm high retaining wall on the squatting toilet (to prevent water from leaking liquid material from flowing to the sewer pipe, and the sewer pipe is blocked), and the toilet is not used.

If there is no doorway stone or the doorway stone is too low, this method can also be used.

4. Fill 15kg of 20kg of water in a plastic bucket, then add the water without leaking the original solution, and stir with a stick for 1 2 minutes.

5. Pour the prepared water slurry into the bathroom tile. (The water is not leaky, the original solution is colorless and tasteless, and it is exactly the same as tap water).

6. Use a broom to sweep from low to high for more than 10 minutes. The main thing is to let the slurry cover all the bathroom floor, so that the gaps used can seep into the slurry.

7. Leave the bathroom after sweeping for more than 10 minutes and wait for curing. (Curing time is 30-50 minutes, depending on temperature).

8. Clean the ground, clean up from the door with a shovel, mainly to clean up the solidified material that can not penetrate into the tile, (very good cleaning), clean up the excess solidified material, please put it in a garbage bag and put it in the garbage bin.

9. Wash the tiles with water. The whole process takes about 1 hour.

Precautions. In case of eye contact, rinse with water.