What should I do if there is water seepage in the bathroom tile joint?

After cleaning the tile joints, try a new type of waterproofing material"The water does not leak"to see if it can meet your requirements, see the instructions on the packaging bag for specific methods.

Fill it up with grout and look at it again. 、。

Porcelain seam treasure: it is mainly made of high-tech polymer blind and high-grade pigments and special additives, rich in color, bright in color, and with gold, silver, pearlescent, stainless steel color, suitable for matching with various color tiles; The whiteness of white is about 95%, the surface strength is high, hard as porcelain, and the apple tree kitchen and bathroom porcelain seam treasure; Its surface is smooth, smooth as porcelain, easy to scrub, dirty and clean, easy to clean, waterproof and moisture-proof, anti-oil and anti-fouling, acid and alkali resistant, avoid sanitary dead ends, can often maintain the original color, and will not pollute the tile when the construction posture is right.

Seek satisfaction.

First of all, check that between the bathroom threshold stone and the door cover, the door cover is generally made above the threshold stone, and the threshold stone is required to be wet, and a row of bricks from the door should also be wet. This prevents water from going out of the doorway. Look at whether the wall tiles are on the floor tiles, generally in, in the wall and floor tiles out of the glue can be managed for a period of time, and the joints should be used with special grouting agents.

Suggestion: 1 Take down the bottom row of wall tiles, make waterproof (preferably polyurethane, not easy to buy, no, use JS), and then put tiles. 2. At the threshold stone, wet paste is used, and the threshold stone is to the edge.

1. If there is a water seepage problem in the waterproof layer, the tiles must be removed, hit the waterproof layer to see the inner wall, and then scrape the putty again, re-make the waterproof layer for the wall, and then pave the tiles.

2. If it is a rupture of the water pipe that causes water seepage, in this case, it is necessary to conduct a pressure test on the water pipe to see if there is a water leakage.

3. If the wall is only leaking because of moisture, you only need to pay more attention to the ventilation and cleaning of the bathroom in your daily life.

4. If the tile gap is not good, there is water seepage. First of all, you need to use cement or caulk to fill the cracks, and make a layer of waterproofing.

Answer 1: If there is a water seepage problem in the waterproof layer, the tiles must be removed, and it is better to hit the waterproof layer to see the inner wall. Then scrape the putty again, make a waterproof layer for the wall, and then lay the tiles. Generally, this method is more complicated, so it is better to check it clearly before proceeding.

2. The second is that the water pipe rupture leads to water seepage, in this case, the water pipe needs to be tested to see if there is any water leakage, if it is indeed caused by the water pipe damage, it is necessary to find out the leakage immediately.

3. If the wall is only leaking because of moisture, you only need to pay more attention to the ventilation and cleaning of the bathroom in your daily life.

4. If the tile gap is not good, there is water seepage. First of all, you need to use cement or bell filler to fill the cracks, and then make a layer of waterproofing.

If the area is small, go to Taobao to buy some glue to repair the seams and deal with the seams.

Bathroom tile joint water seepage treatment method:

1. Cause analysis.

Bathroom tile water seepage must first understand what causes water seepage, there are several reasons: first, the waterproofing of the bathroom is not in place; The second is that the water pipe in the wall is broken and leaks; There is also in the rainy weather, due to the humid air, resulting in water on the surface of the tile; Finally, the tile gaps are not good, and there is water seepage.

2. Solution:

If there is a problem with the waterproof layer, the tiles must be removed, the wall must be beaten to the waterproof layer, and it is better to see the inner wall, and then scrape the putty again, re-make the waterproof layer for the wall, and then pave the tiles, which is generally more complicated.

The second is that the water pipe rupture leads to water seepage, in this case, the water pipe needs to be tested to see if there is a water leakage, if it is indeed caused by the water pipe damage, to find out the leakage immediately, open the wall and replace the water pipe.

If the wall is only leaking because of moisture, you only need to pay more attention to the ventilation and cleaning of the bathroom in your daily life.

If the tile gap is not good, there is water seepage. First of all, you need to use cement or caulk to fill the cracks, and then make a layer of waterproofing.

You knock off the original bricks, and you can do a waterproofing in laying bricks, or you can add waterproofing on top of it

If it is water seeping outside, it will be better to repair it with plastic steel mud, because it is not so troublesome, save trouble, take a look.

It may be that you are not waterproofing well, try to fill the gaps with floor wax.

Use anticorrosive and acid-resistant glass glue.

This situation should be asked directly to the craftsman who gave you the construction, and he knows best.