Hello, in order to find the cause of the leakage in the bathroom, the floor tiles have been smashed

If you only find the leakage but can not find how the water flows to the sinking area, the leakage is useless, the general sinking area leakage is the toilet toilet and the sewer pipe or the flush pipe connection part has water seeping into the sinking area, the general decoration workers for convenience, will be the decoration of the residual mud, waste residue filled into the sinking area, in the toilet and sewer pipe, flush pipe part with cement slurry sealed, but do not take into account the ground or toilet interface leakage, the water is discharged there, As a result, when the water seeps into the sinking area, there is no place for the water to drain, so it has to seep out at the bottom of the sinking area.

If you want to not leak water in the future, you can do it according to my method, 1. Chisel the ground at the location of the sinking pit, clean the filler inside, knock out a new circle around the top, at this time there is no need to do seepage prevention on the surface of the sinking pit, because the surface of the sinking pit is very dirty at this time, and the anti-seepage effect is not good, 2. On the first day, first connect the fecal pipe and the water collection pipe, if the main interface is a cast iron pipe, put glass glue on the interface position, and fill it with cement mortar outside, it must be mortar, not clean cement, After reserving the height of the pipe, put new fine sand or other new filler into the sinking pit, fill it to the appearance of 5 cm from the water nozzle, and the nozzle position is low, and the surrounding high is like a pot, and the filler is covered with a layer of 5 cm thick cement mortar on it, and the proportion of cement should be high, like pouring the floor slab, leveling the nozzle and the new mouth that was knocked on before, and waiting for this layer of mortar to pass a cement oil after collecting water, the purpose of this is to ensure that the water seeping down the ground and the leakage of the flush pipe flow into the fecal pipe together. This ensures that no water will flow into the pit.

3. The next day, it is best to wait for the cement to be hard enough every other day, install the toilet tray, connect the flush pipe, and seal the flush pipe interface position with glass glue.

Fill in new sand or other new fillers, to the reserved height, put water to make the filler solid, because the cement mortar laid the day before is not hard through, it is not recommended to pat this layer of filler, and so after the filler is solid, lay a layer of 3 cm of cement mortar on it, at this time the proportion of cement can be low, if you are in a hurry, you can pave the floor tiles now, but it is recommended to wait for one more day.

If you are sure that it is water seepage in the corner of the sinking area, you can use waterproof paint to treat it, and it is best to knock it all open and do waterproof paint treatment.

If the original waterproof layer has been destroyed, it is recommended to re-do the waterproofing.

If you don't find the leakage point, you can smash it open and redo it waterproofing, and if you find it, you can deal with it locally, it depends on what your specific situation is, and you want to redo it.

After the cause of the leakage in the bathroom is found, the waterproof layer should be redone. After the waterproofing layer is done, it can be stopped for two days, and you can water it to confirm that the waterproofing is done, and then restore the bathroom floor.

First find out a few places in the direction of the water, is there any leakage? For example, there is not a solar drain under the sink, and then there is a tap water inlet, and there is a floor drain for the toilet, in these directions, if you do a good job of waterproofing, he will not leak, because when the toilet is delivered, the whole is waterproof.

I think that in this case, it is necessary to find a professional waterproofing and do it again, so that it can have a good waterproof effect.

Hello now it is normal to destroy the original waterproof layer, otherwise how can you find the leakage location.

Please find a professional waterproof coating construction personnel to redo the waterproof layer.

Didn't find the reason for the leakage in the bathroom, the floor tiles have been smashed open a few pieces to destroy the original waterproofing cooperation of the three countries in the waterproof repair, in this case it should be better to re-do the waterproofing In this case, it should be re-opened, so that it can be.

If this kind of problem occurs, the bathroom waterproofing is especially to be done, so you should wrap all the floor tiles, do a good job of waterproofing, and the effect is good from the floor tiles.

Your problem is a little bit, hello, you can find a leak in the bathroom, the reason is that the floor tiles have been smashed N blocks. And destroy the original waterproof layer, how to do waterproof payment? For this problem, I don't think you can do it yourself, you have to ask a professional to understand the practice of these waterproof layers, they will do better.