What do I need to pay attention to when installing a toilet?

Before installation, the master will conduct a comprehensive inspection of the sewage pipe to see if there is mud, sand, waste paper and other debris in the pipeline, and check whether the ground of the toilet installation is level.

"1. Squatting in the pit to change the toilet, first measure the distance from the center of the drain to the wall. Buy a toilet according to this distance. Don't buy the so-called squatting toilet for sitting, pick a siphon toilet with a suitable hole spacing.

2. Before installing the toilet, be sure to test whether the sewer pipe is unblocked. Method: Fill a bucket of water, quickly pour the whole bucket into the sewer, and pay attention to see if the water level in the sewer has risen. If there is a rise, it must be completely dredged first. Not going up is qualified.

3. Do not seal the screw holes on both sides of the bottom of the toilet bowl during installation. There is no need to install any vents. The screw holes can be vented.

4. If possible, it is best to go downstairs and replace the sewer pipe with a direct elbow. Squatting pits use a trap. It is not good for toilet drainage. Then you don't have to do a second job.

5. If the pipeline is not replaced, please note: some people will flush less in order to save water, which is easy to cause aging or blockage of the pipeline.

The main thing is the sealing of the toilet, which must be tight, otherwise there will be an aftertaste, which is very troublesome, and the ground must be cleaned and leveled, so that the sealing ring can work.

After buying a toilet with the same wall spacing size and sealing cushion, you can start the installation.

First of all, cut the drain short, make the drain 2mm-5mm above the ground as much as possible if possible, lay the position of installing the toilet expansion bolt, clean up the site, and put the sealing cushion around the drain (do not use cement pad).

Then put the drain of the toilet bowl at the drain on the ground and gently put it on, and after confirming that it is placed, you can test the water. If all is well, you're done.

You should choose a toilet with a moderate water storage, if the water storage is too high, it will splash the buttocks, and if the water storage is too low, it will be easy to taste.

2. Pay attention to the glaze of the toilet, the glaze of a good quality toilet should be smooth and smooth without blistering, and the color should be saturated. After inspecting the glaze of the outer surface, you should also touch the sewer of the toilet, if it is rough, it is easy to cause sagging in the future.

3. After the toilet installation is completed, you should try the flushing effect at the first time, the best way is: find a cigarette butt and throw it in, it can be flushed down at once, and the sound is not loud, indicating that there is no problem with the installation link.

4. From a practical point of view, the toilet bowl should first have the basic function of flushing thoroughly. Therefore, the flushing method is very important, and the toilet flush is straight flush, rotary siphon, vortex siphon, and jet siphon. I recommend the jet siphon because of its low noise, strong detergency and good vision in the pit.

5. Generally, the toilet adopts lower drainage. Some people actually measure the distance between the barrels and the results are greater than 400, I don't know how to be good, don't forget, the walls should be tiled. It is recommended to choose a conjoined toilet, which feels wobbly and unsteady.

5. Choose a good toilet sealing wax ring (also called flange ring, wax sealing ring).

Hello! It is necessary to pay attention to the size of the toilet, as well as the anastomosis of the water pipes.

Homeowners can inspect the toilet for breakages. Before installing the toilet, the sewage pipeline should be comprehensively inspected to see if there is mud, sand, waste paper and other debris in the pipeline, and at the same time check whether the ground of the toilet installation position is horizontal. Unpack the toilet, remove it, and attach the hose to the back of the toilet.

The installation accessories of the toilet are mainly angle valves and hoses, which can be purchased by yourself or negotiated with the merchant).

The pit distance of the toilet should be bought correctly, and the specific one who sells the toilet should be asked. Glue should be played a little more, anti-mildew glue, and don't buy bad glue to save more than a dozen yuan.

What do I need to pay attention to during installation? I think that there should be some key parts needed for toilet installation, which should be paid attention to, otherwise there may be some practical problems.

Original 1. Installation method of conventional toilet:

1) Before installation, take out the pipe plug of the ground drain outlet, carefully check whether there is any debris in the pipe, and then clean the area around the nozzle.

2) Make sure that the floor where the toilet is installed is hard and flat, and that there are no floor tiles or other decorative materials, and that if there is sand and gravel debris, it should also be cleaned up.

3) Make sure that the toilet bowl is level before fixing it, and it is recommended to calibrate it with a level.

4) There are two ways to fix the toilet: pull the bolt fixing method: first put the toilet in the installation position, then draw the outline of the toilet foot on the ground, and mark the position of the bolt hole through the installation hole on the toilet.

After making the hole, insert the detonator bolt, apply adhesive at the junction between the toilet outlet and the ground sewage outlet, put the toilet bowl smoothly, pull the bolt firmly, and finally seal the toilet foot with sealant. Silicone adhesive bonding method: draw the toilet bottom caster corridor line on the ground, apply silicone glue inward along the contour line, apply adhesive at the joint between the toilet outlet and the ground sewage outlet, wipe the toilet foot, and place it smoothly in the installation position to bond firmly.

5) Remove the sealant adhered during construction, and be sure to remove it in time before it dries, so as not to be difficult to remove after drying.

6) Connect the water inlet pipe and make sure it doesn't leak.

7) After about one hour of installation, the water is continuously tested several times to ensure that the sewage pipe is unblocked. To test the effect of toilet drainage, the method is to install the accessories in the water tank, fill it with water, put a piece of toilet paper in the toilet and drop a drop of ink, if it can be discharged at one time without leaving a trace, it means that the water is unobstructed.

8) It should be noted that the toilet should not be used within three days after installation, so as not to affect its stability.

2. When the wall-hung toilet is renovated in the waterway, the pipelines and fittings should be embedded in advance, and then protected, and the toilet installation should be completed after the tiles are pasted in the later stage.

3. The smart toilet must reserve the socket position in advance, generally on the left side of the toilet (the right side is the water outlet).