What do I need to pay attention to when installing a bathroom?

1. It is recommended to find a professional electrician for installation. The accidents caused by general bath bombs are due to quality problems and installation problems.

At present, the bath bomb has high power and many wiring, and six or five wires of different colors represent different functions, which are more complex and easy to connect wrongly, and it is easy to burn out the fuselage and leave potential safety hazards. And the reserved line and wiring situation of each family may be different, and some even need to change the line, which is very dangerous to install rashly.

2. Select the bath bomb (thickness) with reference to the height of the ceiling. The general thickness of the integrated bath bomb is 10 20cm, and now the bathroom is generally integrated with the ceiling, which can be installed directly, and the lower ceiling can choose the ultra-thin model, the thinnest can reach 10cm; The same is true for traditional suspended ceilings, but you need to buy a conversion frame when installing. In short, measure the height of the ceiling before buying it to prevent it from being installed after buying, and the thickness of the bath bomb must be less than this value.

For older houses without suspended ceilings, you can choose wall-mounted bath bombs.

3. The lamp bath bomb should be installed in the center of the bathroom, and the air heater bath bomb should be installed above the shower. Many homes install light heaters above the bathtub or shower so that they look like they heat up quickly in winter but are a safety hazard. Because infrared radiation lamps heat up quickly, they are easy to burn the human body if they are too close.

The correct way to do this is to install the bath bomb in the center of the top of the bathroom, or slightly closer to the bathtub, which is both safe and maximizes functionality. The air heater bath bomb can avoid the shortcomings of strong light, a small area can be installed in the center of the bathroom, and a large area can be installed in or close to the bathing position.

There are two kinds of bathroom bath bombs, light heating and air heating, there is a big difference in the installation position, if the installation is not right, not only the heating effect is not good, but the bath will be colder and colder!

Whether the bath bomb is suitable and easy to use has a lot to do with the selection and installation of the bath bomb. First of all, we must pay more attention when buying bath bombs, after all, shopping around is not a loss.

Secondly, Fuxin.com reminds everyone that the installation of bath bombs is still very particular, and it is recommended to find a professional master to help install it. In order to avoid problems in the use of the bath bomb due to unreasonable installation.

1. Bath bombs generally have multiple functions, such as heating, lighting, hot air, exhaust, etc., and enough wire circuits should be left.

2. If there is a suction function, be sure to drill the air outlet in front of the ceiling 3, now it is generally an aluminum alloy gusset ceiling, just press the bracket on the line, if your bath bomb is 600 * 600, then the main keel must leave this space, if it is 300 * 600, you must consider the direction of the main and auxiliary keel (tell the ceiling master specifications), the bath bomb must leave appropriate space behind it.

If the ceiling has been completely done, the joint of the note line must be connected firmly to avoid poor contact, use waterproof tape, connect the bath bomb to the top, try the function on the switch respectively, and then connect it according to the instructions on the switch, and call it a day.

Avoid potential safety hazards Bath bomb installation tips.

When installing the bath bomb, it is best not to be too low from the top of the head, theoretically it should be above 40 cm, so as to ensure that it is both warm and does not burn the skin.

The bath bomb power wiring system should be standardized.

The power of the bath bomb can reach up to more than 1100W, therefore, the power wiring of the installation of the bath bomb must be a waterproof line, preferably a multi-wire copper core wire of not less than 1mm, all power wiring must be embedded in the wall with plastic hidden pipes, and no open wires are allowed to be set, and the power control switch of the bath bomb must be a qualified product with a waterproof capacity of more than 10A.

1: Look at the packaging, the production and packaging requirements of regular family bath bombs are very high, and the appearance of the product is smooth, no scratches, consistent color, and the installation of exposed parts is firm. And the appearance and packaging of shoddy home bath bombs are mostly rough.

If even the appearance and packaging of the product look rough, then how can we make our customers feel safe?

2. Power on the test operation, power on to check the following conditions: whether the function switch is working normally, whether the heating effect is obvious, whether the lighting ventilation is normal, whether there is jitter and noise.

3. Look at the registered trademark, the family bath bomb produced by the regular manufacturer, the outer packaging box and promotional materials are printed with a clear registered trademark and R logo. Generally, the logo is on the top right of the product brand or logo. At present, the inspection mark is a very effective and direct means of inspection for consumers.

4: Look at the manufacturer, there are not many regular manufacturers of family bath bombs, therefore, many fake and shoddy products are marked with the address of the manufacturer is very vague. Counterfeit and shoddy products generally use fake names and false addresses. In the process of sale, it was declared that it was produced by brothers.

The above is the introduction of installing bath bombs in toilets. With the development of time, the participation of bath bombs, the toilet is becoming more and more comfortable, many people like to read books in the toilet, not only because the toilet is more comfortable to sit, but also because the bath bomb is very warm, which makes people very reluctant to leave, but it is better not to stay in the toilet longer.

The following is an introduction to the installation preparation of the two most commonly used and safe heating bath bombs: Generally, the line will be laid during the hydropower transformation. How do I install a bath bomb?

1. Stay wires (wires) :(1) 4 sets of lines are required for general lamp heating baths (2 groups of lamp warming, 1 group of ventilation, 1 group of lighting) by 5 wires (1 neutral line and 4 control live wires above the top, 1 fire inlet line and 4 control fire wires at the switch below) (2) Air heating bath bomb (PTC ceramic heating element heating) requires 5 sets of wires, (1 group of lighting, 1 group of ventilation, 2 groups of PTC heating sheets, 1 group of internal circulation hair dryer negative ions) How to install a bath bomb? 2. The air outlet ventilation fan needs an air outlet to suck the indoor air out.

The diameter of the air outlet is generally 10CM, and it is generally necessary to open it before the ceiling. How do I install a bath bomb? 3. The reserved opening of the installation port is generally 300*300, and there are also bath bomb openings of about 300*400.

According to the requirements and methods of the reserved mounting port for different gussets, there are some differences *300 or 300*600 aluminum gusset ceiling: Leave a piece of 300*300 gusset position without installation (2), strip aluminum strip plate, it is best to confirm the size of the opening of the bath bomb when installing the gusset, leave the installation hole when installing the gusset, and prepare two stronger wooden strips larger than the main keel span of the ceiling on the hanging, for the installation of the bath bomb.

3), plastic steel gusset, basically the same as above (4), waterproof gypsum board ceiling and sauna board ceiling, because to confirm the position of the keel, please also determine the size of the bath bomb installation opening when installing the gusset. How to install a bath bomb and what should I pay attention to when installing it? First determine the position where the person stands in the bathroom when bathing, the person should face the shower head (shower head), and the upper back of the human body is the position where the bath bomb is installed.

The reason why the bath bomb is installed on the back and top of the human body is that in addition to the heat of the bath bomb can heat the air in the bathroom, it can also directly radiate heat to the back of the human body. Because when bathing, it is the back that people feel the coldest. Be careful not to install the bath bomb on top of a person's head.

The above position is an example of a standing shower with a human body, and if a bathtub is used, a bath bomb is installed in the center of the bathtub. The bathroom area is large, and with the lighting of the bath bomb, there can also be additional lighting. Do you know how to install a bath bomb?

The top priority: the power wiring system should be standardized.

The power of the bath bomb can reach up to more than 1100W, therefore, the power wiring of the bath bomb must be a waterproof line, preferably a multi-wire copper core wire of not less than 1mm, all power wiring must be embedded in the wall with plastic hidden pipes, and no open wire is allowed to be set, and the power control switch of the bath bomb must be a qualified product with a waterproof capacity of more than 10A, especially the installation of bath bombs in the bathroom of the old house should be standardized.

Installation location: It should be installed in the top center of the bathroom.

Many homes install it above the bathtub or shower, and although it looks like it heats up quickly in winter, it is a safety hazard. Because infrared radiation lamps heat up quickly, they are easy to burn the human body if they are too close. The correct way is to install the bath bomb in the center of the top of the bathroom, which is both safe and allows the maximum function of the bath bomb.

Point 3: The thickness of the bath bomb should not be too thick.

Consumers must pay attention to the thickness of the bath bomb should not be too thick when purchasing, and it is advisable to be about 20 cm. Because the bath bomb should be installed on the roof, if you want to install the bath bomb, you must add a layer of roof below the roof, which is what we often call the PVC ceiling, so that the second half of the bath bomb can be sandwiched between the two tops, if the bath bomb is too thick, it will cause decoration difficulties.

In addition, after the bath bomb is installed, it is necessary to pay attention to maintenance when using it, and keep the bathroom ventilated, clean and dry frequently, so as to prolong the life of the bath bomb.

The bathroom is an indispensable part of the home. Nowadays, people have higher and higher requirements for the quality of life, so the bath bomb is also very important for the bathroom. When we buy the bath bomb back and install it, it can be used normally.

So, what matters and details do we need to pay attention to when installing a bath bomb? Pay attention to details in installation If you have a shower room at home, experts recommend installing a bath bomb on the bathroom ceiling, instead of installing a bath bomb in the shower room. First, because there are generally supporting shower facilities in the shower room or shower screen, and the effective area of the shower room is too small and the height is low, compared with other spaces, the temperature in the shower room is very high, and there is no need to install a bath bomb in the shower room; If you install a bath bomb without special waterproof performance, the water vapor in the shower room is too concentrated to make the bath bomb damp, but there will be potential safety hazards in the bathroom environment When purchasing, you should pay attention to choosing a bath bomb according to the bathroom area.

Generally, because the small area of the small bathroom and the large water mist, it is best to choose a better exhaust effect. In addition, if it is a newly renovated room, you can consider installing a ceiling-mounted bath bomb, because the ceiling-mounted bath bomb does not take up space, and the style is novel, the appearance is fashionable, each corresponding to a different decoration style, the choice is larger, and it is best to do it at one time when decorating. If it is an old house, choose a bath bomb according to whether there is a suspended ceiling, whether the thickness of the ceiling is sufficient, whether there are enough plugs, etc.

Safety Since electrical appliances are used in a humid environment, and there have been accidents with bath bombs before, it is best to choose brand products with relatively guaranteed safety performance, not only the product quality is trustworthy, but the installation and after-sales service are relatively guaranteed. It is understood that brand products are generally guaranteed for one to three years, and can be installed and repaired free of charge.

In addition to bath bombs, there is also a type of heater that can be used to keep the bathroom warm. Because it is waterproof, it can be used in both bedrooms and bathrooms, but to be on the safe side, it is better to choose a bath bomb that is specifically designed for bathroom heating. Bath bombs not only need to pass the brand and quality, but more importantly, safety!

Therefore, in the process of installing bath bombs, the above matters should be paid attention to!