What should I pay attention to when installing a toilet?

The toilet is an indispensable sanitary product in the toilet and an indispensable part of our lives. The emergence of the toilet has brought us a lot of convenience, many owners are concerned about the purchase, quality and appearance of the toilet, often ignore the installation of the toilet, think that the installation of the toilet is very easy, the installation of the toilet is not as simple as you think. You should be very clear about these precautions.

Banquet God year to intercept the sewer, general decoration, the bathroom will be set up sewer, this sewer is closed, only when needed to cut the sewer, when the toilet is installed to cut the sewer. It is only necessary to fill the cut tube with the flange ring.

> book two small holes, which are kept on the toilet. Generally speaking, for the toilet to work properly, it is necessary to leave two small holes in the edge of the toilet, with the aim of making it smoother and not clogged when the sewer drains out of the sewer. Using fastening screws, the use of fastening screws can make the toilet installation more aesthetically pleasing, preventing the screws on the toilet from rusting.

Because if the screws on the toilet are rusty, the whole bathroom will smell, and the experience of using it is not good. Glass adhesives.

> glass adhesive is a very important auxiliary material, which can park the toilet on the bathroom floor without causing the danger of tilting and collapsing, and can also install the flange ring in the sewer to keep the whole toilet in a relatively stable state. The appearance should be good, and it is necessary to gently observe whether there is glaze, glitter, ripple cracks, pinhole impurities on the inner and outer surfaces, whether the appearance is symmetrical, and whether it is stable and unshakable on the ground. Whether the water in the water tank is a refinery product, whether it has a liter and water saving function, whether the water tank and sewer are glazed, which part of the toilet is tapped, and whether the sound is clear.

Where > potholes, it is essential to know the correct size of the sewer center on the wall before buying. It is usually divided into places 300,400 mm deep. If you don't understand, you can ask the construction site how much my pit is, listen to the opinions of the construction site, ask how big the pit is, and the domestic toilet will definitely not lose to the so-called imported brand in that regard.

Most of the products known as imported brands are also manufacturers in China that can meet the requirements of the professional branch of that big brand.

When installing the toilet, it is necessary to carefully grind the sail and pay attention to check whether the water parts in the tank are genuine products, and whether the pit distance is reasonable, generally divided into 300 wide hail and 400 millimeters; The appearance of the toilet bowl is whether the oil surface of the early type is shiny and smooth.

When installing the toilet, you must pay attention to buying a better quality toilet, and secondly, you must pay attention to the gap left by the original when installing, and finally you can also use some examples to fix the toilet bowl, so that the Mabi pants bucket will not be easily loosened.

First of all, it is necessary to choose the appropriate glue to widen, and it is necessary to inspect and clean the sewage pipeline, and to make the ground very flat, and to determine the appropriate position of Heshan Tuoliang, and then to reserve the wall distance in advance, and also install expansion bolts.

\"1. Squatting in the pit to change the toilet, first measure the distance from the center of the drain to the wall. Buy a toilet according to this distance. Don't buy the so-called squatting toilet for sitting, pick a siphon toilet with a suitable hole spacing.

2. Before installing the toilet, be sure to test whether the sewer pipe is unblocked. Method: Fill a bucket of water, quickly pour the whole bucket into the sewer, and pay attention to see if the water level in the sewer has risen.

If there is a rise, it must be completely dredged first. Not going up is qualified. 3. Do not seal the screw holes on both sides of the bottom of the toilet bowl during installation.

There is no need to install any vents. The screw holes can be vented. 4. If possible, it is best to go downstairs and replace the sewer pipe with a direct elbow.

Squatting pits use a trap. It is not good for toilet drainage. Then you don't have to do a second job.

5. If the pipeline is not replaced, please note: some people will flush less in order to save water, which is easy to cause aging or blockage of the pipeline. **

The forum has a special topic, which is very useful, and it is recommended that you check it out. The majority of Chaojia netizens have a lot of wisdom ---

Installation points.

1. Installation begins after receiving and accepting in person.

Toilets should go through strict quality inspection before leaving the factory, such as water testing, visual inspection of appearance, etc., products that can be sold on the market are generally qualified, but remember, no matter how big the brand, but also in front of the merchant to open the box and inspect the goods, check whether there are obvious defects and bruises, and whether there is color difference in each part.

Second, pay attention to adjusting the ground level.

After buying a toilet with the same wall spacing size and sealing cushion, you can start the installation. Before the installation of the toilet, a comprehensive inspection of the sewage pipe should be carried out to see whether there is mud, sand, waste paper and other debris in the pipeline, and at the same time check whether the ground of the toilet installation position is horizontal. Cut the drain short, and if possible, make the drain 2mm-5mm above the ground.

3. Check whether there is leakage after debugging and installing the water tank accessories.

Check the water pipes first, drain the water for 3-5 minutes to rinse the pipes to ensure the cleanliness of the water pipes; Then install the angle valve and the connecting hose, then connect the hose with the installed water tank fitting inlet valve and connect the water source, check whether the water inlet and sealing of the inlet valve are normal, whether the installation position of the drain valve is flexible, whether there is any jamming and leakage, and whether there is any leakage and installation of the inlet valve filter device.

Finally, test the sewage effect of the toilet, the method is to install the accessories in the water tank, fill it with water, try the flushing of the toilet, if the water vortex is very rapid and flush quickly, it means that the water is unobstructed, on the contrary, to check whether there is a blockage.

It's okay to come to the Opai wooden store and talk to us about the decoration!

After buying a toilet with the same wall spacing size and sealing cushion, you can start the installation.

First of all, the sewer is sawed short, if the conditions permit, the sewer is 2mm-5mm above the ground as much as possible, the site is cleaned, and the sealing cushion is put around the sewer (do not use cement pad). It is best not to install toilet expansion bolts, so as not to damage the waterproof layer, and lay glass glue around the surrounding area of the toilet bowl to fix the toilet. It can only be hit on the side, and later repairs can be cut with a blade.

Then put the drain of the toilet bowl at the drain on the ground and gently put it on, and after confirming that it is placed, you can test the water. If all is well, you're done.

Remember to seal the two small holes in the back of the toilet (if you don't have one, it's best). The seal cannot be saved.

The master teaches you to install the toilet, you must pay attention to these steps, don't be indifferent!

1. Before buying, you must first determine whether your sewer pipe is discharged horizontally into the wall (the interface is on the wall behind the toilet) or into the ground (the interface is on the ground under the toilet). If it is discharged into the ground, the most important thing is to measure the distance between the center point of the sewer pipe and the wall (that is, the pit distance); If it is discharged horizontally into the wall, the distance between the center point of the sewage outlet and the ground after it is done should be measured.

2. Choose the style and color that matches the whole interior.

3. Look at the glaze of ceramics: it should be smooth, smooth and crystal bright; There are no obvious needle holes, glaze gaps and cracks; Tap the toilet, the sound is crisp and pleasant, there is no cracking sound, no deformation of the shape, etc.

4. A good toilet has thorough sewage discharge, large flushing area, low noise, water saving, smooth surface and low water absorption.

5. The toilet is divided into first-class products, second-class products, and third-class products.

6: 100 yuan to 1,000 yuan for domestic production, 1,000 yuan to 10,000 yuan for imports.

1.Before installation, confirm that the wall spacing of the reserved sewage pipe is consistent with the selected product, and install the fixed expansion bolts. (Note: The ground sewage pipe should be flat with the ground so that it can be sealed with the sealing ring).

2.Place the toilet bowl correctly (the toilet drain outlet is aligned with the sewage outlet on the ground or wall), use a pen to accurately trace the position of the expansion bolt and the bottom of the toilet bowl, and drive the appropriate expansion bolt into the ground.

3.Install the toilet seat, check whether the water inlet and drain parts are installed, install the angle valve (check if there is any water leakage), install the toilet seal, etc.

4.Align the screw holes and slowly lower the toilet, so that the expansion bolt passes through the mounting hole at the bottom of the toilet, make sure that the toilet seal ring is aligned with the sewage pipe, and press down on the toilet bowl with a slight or swinging action until the toilet is stable. (Suggestion:.)

Keep the gap between the back wall and the wall of the toilet tank 19 6mm). Finally, depending on the situation, wrap a closed sealant line along the bottom of the toilet bowl, or apply a sealed glass glue (neutral glass glue).

5.Install the inlet hose, tighten the mounting nut to make the toilet bowl stable, and put a decorative cap on the expansion bolt. (According to the actual local situation, adjust the water tank accessories to the appropriate water level:

Install the buttons: Close the lid of the water tank: test flush:

Install and adjust the toilet seat according to the installation instructions: check the water inlet for leaks).

Pay attention to whether the hole spacing is appropriate, and the sewer pipe should be level with the ground and polished smooth.