-
Anonymous users2024-01-24Dear, hello, first of all, I didn't see the position and condition of your puncture, don't dare to be rash, it's best to have a picture, I now provide several methods, I hope it will help you, 1If it is punctured in the place where the hand can reach, and the hand can go down, it is recommended that the punctured place be cleaned with sandpaper or saw blade, if it is not big, it can be blocked with AB glue, if it is large, more than 1CM, it can be sanded and sealed with glass glue (this method is applicable in the middle of the floor, because of fear of leakage downstairs).
2.FIND RUBBER GLOVES, ABOUT 2MM THICK KIND, CUT INTO ABOUT 3CM WIDE STRIPS FOR STANDBY, POLISH AND CLEAN THE PUNCTURED PLACE, SMEAR WITH PVC GLUE, AND THEN PULL THE CUT OUT STRIPS CLOSER TO THE UPPER 5CM OF THE LEAKAGE POINT IN A HALF-MATCHED WAY TO START WINDING, WRAP TO THE BOTTOM OF THE LEAKAGE POINT 5CM, RECIPROCATE MORE THAN 2 LAYERS, AND FINALLY USE TAPE OR TAPE TO SPARE A LAYER OUTSIDE, YOU CAN (THIS METHOD IS SUITABLE FOR THE FLOOR BELOW, CAN BE SEEN AND EASY TO MAINTAIN, REMEMBER THAT THE STRIP MUST BE TIGHTENED, Finally, the head of the strip must be tied firmly to prevent it from popping off).
3.Cover a thinner than him inside the leaking sewer pipe, and then use the plugging spirit to seal the gap between the two pipes, (this method is suitable for the sewer pipe with thicker pipes, remember that the thin sewer pipe must wrap a few circles of tape around the lower mouth, or use other methods to prevent the leak-proof material from falling into the sewer pipe when plugging the peak.)
-
Anonymous users2024-01-23Find a bricklayer. Dismantle the floor drain and replace the floor drain pipe. The total cost depends on the local labor cost, the price of floor drain fittings, etc., and generally all can be done within 300 yuan.
Leibangshi - home waterproofing expert.
-
Anonymous users2024-01-22If the punctured pipe is not buried, you can use a small section of the same diameter pipe to open a third of the batch, and apply the pipe glue to glue it.
-
Anonymous users2024-01-21Looking for a plumber, you can generally get it within 300 yuan.
-
Anonymous users2024-01-20Looking for a plumber, it should not be very expensive less than 500 yuan.
If you have trouble changing the tube, you can dispose of the garbage and glue on the surface of the joint, stop the water and wait for drying, brush the joint with a group A and B quick-drying epoxy resin, and then wrap a layer with glass fiber or a breathable thin cloth, and then coat the glass fiber with epoxy resin. These processes are done continuously, without stopping. This remedy is almost the same as removing the pipe and starting from scratch, but it will be more ugly.
Now the sewer pipes are all engineering materials Your home should be an old house It's best to change the pipes Otherwise, it will corrode Choose the floor drain Jindel floor drain The water area of the Jindel floor drain panel is more than 2800 square millimeters, plus the unique siphon function, to ensure that the drainage volume can reach up to 80l min under normal conditions, which is much greater than the municipal tap water pressure, 6 points burst pipe flow. The height of the water seal reaches the national requirement of 5cm, and the water storage capacity of the water seal exceeds 300ml, which can ensure that it does not dry up for 30 days.
The part of the sewer pipe in the cement will not be broken, the dredging agent will not corrode the pipe, the seepage is generally from the outer edge of the drain to seep down, you have to beat the drain around three or four centimeters deep, and then use high-grade mortar to re-repair in order to no longer seepage.
Recently renovated, the first floor sewer pipe embedded parts are broken, you can re-open, re-open the new pipe, replace it.
It will not solve the problem at the root, and it will leak through the gap between the two pipe diameters.