How to install a kitchen sink faucet?

1. Close the sluice of the faucet.

2. Put away the residual water in the faucet to avoid splashing water everywhere after disassembling the faucet.

3. Pry open the protective piece on the faucet handle, which is generally glued on.

4. Use a screwdriver to unscrew the screws on the handle.

5. Take off the handle, and the handle is put on the bite longitudinal tooth pattern.

6. Use a wrench to remove the shaft and replace the red rubber washer.

7. The small porcelain piece under the faucet washer, the left side is placed at the bottom, and the right side is placed above, and the front and back cannot be reversed, and the water will not be closed.

8. Finally, tighten the faucet with a wrench, and it will be fine.

Installation method" [first step] 62616964757a686964616fe78988e69d8331333433616139: preliminary preparation.

1.Open the package of the stainless steel sink, take out the instructions to check whether the components in the package are complete, the components of the general stainless steel sink have the tank body and drainage components, different types of stainless steel sinks may be different, this can be determined according to the specific situation.

2.Take out the sink and make the opening of the sink table according to the opening template attached to the box. Then check the sink to see if the silencer block is degummed, and if so, please re-attach it.

3.Check whether there are cracks in all parts of the faucet of the sink fittings, and whether the sealing rings at both ends of the connecting pipe are missing, misaligned, damaged and other faults, so as to avoid water leakage after the faucet is installed and increase the difficulty of installation work. [Step 2]: Install the stainless steel sink.

1.The drain of the stainless steel sink in the kitchen is to be left in the sink cabinet, and the angle valve must be installed before we install the sink. In the process of installing the faucet, do not remove the packaging on the outside of the faucet, and only remove it after the installation is completed, so as to avoid damaging the outer surface of the faucet during the installation of the faucet.

2.If the installed faucet has the function of hot and cold water, be sure to confirm the accuracy of the connection of hot and cold water, and ensure that the left end of the faucet of the stainless steel sink is connected to the hot water pipe, and the right end is connected to the cold water pipe.

3.When installing bellows and braided pipes, we must pay attention to the size of the tightening force, too large or too small will have a certain impact on the stainless steel sink, too large is easy to damage the thread, too small will lead to insufficient sealing and water leakage.

4.After the above work is completed, you can start to do the water commissioning of the stainless steel sink.

5.After the successful commissioning of the water, the installation of the stainless steel sink is completed.

The kitchen sink faucet should be placed in a suitable position in the corner, connected to the angle valve switch, and installed according to the instructions.

How to install the sink!

1. The style of the sink selected by each family is different, so the position of the sink set aside on the inside of the table should be consistent with the volume of the sink, and the approximate size of the sink should be informed to the countertop supplier when ordering the countertop, so as to avoid the problem of rework.

2. Before installing the faucet and installing the sink, the faucet and the water inlet pipe should be installed. When installing faucets, it is not only required to be installed firmly, but also that there should be no water seepage at the joints.

1) Install the water inlet pipe of the faucet and connect one end of the water inlet pipe installed on the faucet in advance to the water inlet switch, pay attention to the firmness of the connection during installation, and also pay attention to a detail, that is, the position of the hot and cold water pipe, do not make mistakes left and right.

2) The overflow hole of the sewer pipe installed with the overflow hole is a protective hole to avoid the overflow of the sink, so when installing the sewer pipe of the overflow hole, it is necessary to pay attention to the tightness of the connection between it and the tank, and ensure that the sewer pipe of the overflow hole does not leak by itself.

3) Install the sewer pipe of the filter basket. When installing the sewer pipe under the filter basket, the main attention should be paid to the connection between the sewer pipe and the tank, which should not only be firm, but also sealed.

Kitchen decoration sink needs to pay attention to accessories, the frequency of use of the sink is high, and the surface is summarized for the home, and the precautions for the purchase of the sink are summarized.

Edition 1The sink must be basketed to prevent the right to block the water and clean the toilet 2The sink water must be made S bend, otherwise the aftertaste is 3The sink dragon hand must be easy to clean with the arm can push the kind 4The sink countertop is easier to take care of, especially the rusty steel sink, the rusty steel countertop has poor adhesive adhesion than stone.