Bathroom vitrified brick pasting method

The method of vitrifying tiles in the bathroom is as follows:

1. Clean up the base layer, clean up the mortar slag, dust, oil stains, etc. remaining in the base layer, and water and moisten it in advance.

mm thickness 1:3 cement mortar priming, priming should be layered, each layer thickness should be 5mm or 7mm, and then smooth and rub the hair.

3. Wait for the bottom layer to be ashed.

When the sixth and seventh layers are dry, according to the requirements of the drawings, the specifications of the bricks and the actual conditions, the bricks are arranged and the elastic line is carried out.

4. Use 1:3 cement mortar to stick the corner bricks on the ground as a reference point to control the surface flatness of the floor tiles.

5. Cushion the bottom ruler, calculate the elevation of the lower mouth of the next brick accurately, the bottom ruler is generally 10mm lower than the ground, and put the bottom ruler on this basis, which should be horizontal and stable.

6. Before the veneer bricks, the facing bricks should be soaked in water for more than 2 hours, and then taken out to dry for later use.

7. Wipe the 8mm thick cement mixed mortar bonding layer, scrape it flat, paste the surface brick with the wipe from top to bottom, require the mortar to be full, and remove and repaste when the ash is lost, and check the flatness with a ruler at any time, while ensuring that the width of the gap is consistent.

8. After pasting the self-inspection without hollowing, unevenness and straightness, wipe it clean with cotton yarn, wipe the joints with white cement slurry or pat dry cement, wipe the plain slurry in the joints with a cloth, and wipe the brick surface clean.

There are two methods for vitrified brick wall construction technology.

1. Dry hanging: It is to coat the corners with AB glue, and add a few stainless pendants. When the AB glue is dry, apply the cement on the back of the vitrified tile and then stick it to the wall.

One of the drawbacks of this method is that the vitrified bricks on the wall will be hollowed out for a long time, so that the vitrified tiles on the wall will completely rely on a few points of AB glue and pendants. If this is the case for a long time, the AB glue and stainless steel pendant on the vitrified brick will be loosened, so that the vitrified brick will be detached from the wall.

Second, the vitrified brick wall wet paste: that is, the back of the tile is not with AB glue, is coated on the back of the tile with cement mixture, this layer of cement mixture can be firmly bonded with the back of the tile and the mastic wall, and the entire tile back and the wall are bonded, not a few points of bonding. In this way, the phenomenon of hollowing out the drum will no longer occur.

Even a single vitrified tile with a large area is no problem.

Precautions.

1. When paving ceramic tiles, you should carefully read the manufacturer's instructions, and the manufacturer will generally have a very detailed description. Before use, consumers should check whether the color number and size indicated on the outer packaging are the models they ordered, and whether the bricks of the same color number have defects such as color difference and broken threads.

2. Before paving, the tiles often need to be soaked in clean water for 20-30 minutes before they can be paved after filtering out the water.

3. The cement grade used for paving should be a low grade, and the cement thickness should not be too large, generally not more than 5mm. When laying bathroom floor tiles, be sure to use non-slip texture. Generally, matte or shallow concave and convex floor tiles are very suitable for slippery floors after bathing, to protect the owner from slipping and injury, and the floor of the bathroom should be 10-20 mm lower than the floor of other rooms.

4. When paving tiles, the position and size of the floor drain should be considered. Usually, the floor tiles are laid with a slope of 1% leakage, and the floor drain is the lowest to facilitate drainage. The joints of the floor tiles should be of the same thickness and align with the joints of the wall tiles.

There are two methods for vitrified brick wall construction technology.

1. Dry hanging: It is to coat the corners with AB glue, and add a few stainless pendants. When the AB glue is dry, apply the cement on the back of the vitrified tile and then stick it to the wall.

One of the drawbacks of this method is that the vitrified bricks on the wall will be hollowed out for a long time, so that the vitrified tiles on the wall will completely rely on a few points of AB glue and pendants. If this is the case for a long time, the AB glue and stainless steel pendant on the vitrified brick will be loosened, so that the vitrified brick will be detached from the wall.

Second, the vitrified brick wall wet paste: that is, the back of the tile is not with AB glue, is coated on the back of the tile with cement mixture, this layer of cement mixture can be firmly bonded with the back of the tile and the mastic wall, and the entire tile back and the wall are bonded, not a few points of bonding. In this way, the phenomenon of hollowing out the drum will no longer occur.

Even a single vitrified tile with a large area is no problem. Hope it helps,

The construction process is as follows: (1) Clean up the base layer, clean up the mortar slag, dust, oil stains, etc. remaining in the base layer, and water and moisten in advance. (2) 12mm thickness 1:

3. Cement mortar priming, priming should be layered, each layer should be 5 7mm thick, and then smooth out the hair. 3. Wait for the bottom layer to be ashed.

When the sixth and seventh layers are dry, according to the requirements of the drawings, the specifications of the bricks and the actual conditions, the bricks are arranged and the elastic line is carried out. 4. Use 1:3 cement mortar to stick the corner bricks on the ground as a reference point to control the surface flatness of the floor tiles.

5. Cushion the bottom ruler, calculate the elevation of the lower mouth of the next brick accurately, the bottom ruler is generally 10mm lower than the ground, and put the bottom ruler on this basis, which should be horizontal and stable. 6. Before the veneer bricks, the facing bricks should be soaked in water for more than 2 hours, and then taken out to dry for later use. 7. Wipe the 8mm thick cement mixed mortar bonding layer, scrape it flat, paste the surface brick with the wipe from top to bottom, require the mortar to be full, and remove and repaste when the ash is lost, and check the flatness with a ruler at any time, while ensuring that the width of the gap is consistent.

8. After pasting the self-inspection without hollowing, unevenness and straightness, wipe it clean with cotton yarn, wipe the joints with white cement slurry or pat dry cement, wipe the plain slurry in the joints with a cloth, and wipe the brick surface clean.