Remove the bedroom in the red circle and make it into a high ceilinged living room, and remove the w

In general, the height of the house is about 4 meters, which belongs to the high ceiling space, but when it is sold, it is only sold as a floor, and the price is about the same. After handing over the house, many customers like to divide the space of this height into two floors, and then convert the three-dimensional space, the lower space can be used as a living room or dining room, and the upper floor is used as a bedroom. The high-ceilinged house has a wide range, which can be used for office and residence, depending on how you choose.

Household gas rapid water heater products have been developed in China for many years, according to the waste gas produced by the combustion of the water heater and the different ways of air supply required, the representative products of each stage of development include: in-line type, flue type, forced exhaust type, forced exhaust type, the most produced products in China are flue type and forced exhaust type, each accounting for about 50%. Flue water heaters are usually powered by two dry batteries, and the exhaust gas generated by combustion is discharged to the outside through the smoke exhaust pipe by natural suction force, which is susceptible to the influence of outdoor wind and causes poor smoke exhaust, so it is more suitable in areas with less wind throughout the year.

The forced exhaust water heater needs to be connected to a 220V power socket, and the exhaust gas generated by combustion is discharged to the outside through the exhaust pipe by relying on the suction generated by the internal fan of the water heater, so the use of the water heater is relatively safe, but it cannot be used in the case of a power outage at the user's home. From the point of view of product price, the price of flue water heater is relatively cheap, and the price of forced exhaust water heater is relatively expensive. In the past two years, the water heater with the function of automatic constant temperature of hot water outlet has gradually entered the market, this product in the process of use when the user sets the appropriate outlet temperature, the water heater can ensure that the outlet temperature is constant within a certain range at any time, which greatly improves the comfort of use, because the product generally produces a large amount of water, especially suitable for the living environment where there are multiple locations that need to supply hot water at the same time.

How to choose a domestic gas water heater? 1. Users who use LPG water heater products must pay attention to the selected pressure reducing valve (the part connected between the water heater and the LPG cylinder). 2. Consumers must carefully read the safety instructions and warning signs pasted on the manual and product shell before using the gas water heater, including:

The product is suitable for the warning of the type of gas, the precautions for ventilation and ventilation during use, and the grounding problem of the AC power supply. 3. In the process of long-term use of gas appliances, consumers should regularly check whether there is gas leakage in the gas connection pipeline, and replace the gas connection hose or joint that may leak due to material degeneration after long-term use. 4. It is strictly forbidden to dismantle the internal structural components of gas water heater products without permission or non-professionals, and when you feel that there is a problem, you must contact professional maintenance personnel for inspection and maintenance in time.

Try to reduce the use of the tip to process the workpiece: at the position of the tip of the ball nose cutter, in the actual machining, the processing line speed is 0, that is to say, in fact, the tool is not cutting, but grinding, in the actual processing, the coolant can not be added to the cutting area at all, which leads to the cutting heat is relatively large, and the tool life is reduced.

2) For the straight wall, it is best to use the processing method of contour profile for processing: it is necessary to minimize the phenomenon of the ball nose cutter of the woodworking engraving machine processing down along the straight wall. Comparatively speaking, machining along straight walls upwards is a very good method, but it is difficult to separate them in actual machining.

Let's compare the differences. This is the case of downward machining with a ball nose cutter.

3) The use of contour to process straight walls can reduce the phenomenon of downward processing. It can be avoided if you can use the phenomenon of "bottom-up knife walking". In the use of "from the bottom to the top" to first consider whether the first knife is too large, if there is a relatively large residue left at the root of the surface after the above processing, then the first knife processing amount may be too large.

This does not protect the tool but destroys it.

4) Pay attention to the processing of the deep groove of the woodworking engraving machine: when processing the deep groove, the tool may sink completely, because the chip groove of the ball nose cutter is relatively small, in the processing of more sticky materials (such as copper), when the feed speed is fast, it is easy to break the knife. Tuoqi three-dimensional engraving machine reminds that when using the ball nose knife of the woodworking engraving machine for processing, it is necessary to pay attention to chip removal.

Specifically, you have to ask Dexin Design Agency, they are professional, we don't understand.

The high ceiling decoration of the living room should do a good job of partitioning the space. Many homeowners consider dividing their living rooms with floors that are more than twice as tall as their average home, so they will consider dividing these living rooms so that the usable area will be doubled. Therefore, for the decoration of the living room with high ceilings, it is best not to make a room with partitions, and you can take a partial partition method.

But according to some experts, it can be a bit incongruous and can look awkward. If you feel that the area of the house is small, you can also make a small partition on the turntable of the stairs, and then put some chairs on it, slowly sip tea, and slowly look into the distance, which gives people a very good feeling.

Non-standardized, unrecognized drawings do not see anything, and have little effect, mainly look at the contract and annexes.

1. It is best not to partition the high living room to make a room, and a partial partition can be taken.

Local partitions can be used to increase the sense of hierarchy in the living room. If you really feel that the area of the house is too small, we can make a small partition near the turntable where the stairs turn up, and put a rattan chair and a few chairs on it, you can drink tea and look down on the living room, which is also good.

2. The top surface of the high-ceilinged living room is empty.

The high living room space is large, and if the decoration is less, it will appear very empty, making people feel empty, so the top surface can be artistically processed to show taste. How to do the top surface is also a difficult problem. Generally, you can design a very atmospheric background decoration.

You can ask the painter to make a large painting, and the painting content should follow your own decoration style.