-
Anonymous users2024-01-24I look for someone who installs a toilet overflow preventer. The company specializes in selling and installing toilet overflow preventers. It is an anti-overflow device researched by the 809 Research Institute of Shanghai Aerospace Bureau.
Free door-to-door delivery within the Shanghai Outer Ring Road. Door-to-door within one hour of the inner ring. Causes of flush toilet overflow:
In multi-storey toilets, fecal spraying often occurs on the second and third floors. The odor and overflowing water bucket are very troublesome, and the main reasons are as follows: 1
The diameter of the outdoor sewage pipe or the volume of the sewage pipe has been overloaded, causing the sewage water level to rise to the top of the well, and the sewage and the entrained airflow cannot be discharged, that is, it will be reversed from the toilet on the second floor. Splashing or flooding in pools. 2.
The settlement of the house forms the reverse slope of the sewage pipe. Gas. Poor water excretion causes backspray.
3.The funnel-shaped blockage at the turning point of the riser is not smooth, resulting in backspray. 4.
A large amount of groundwater seeps into the outdoor sewage well, resulting in poor drainage of the pipeline at full load 5In the normal pipeline, when each building discharges sewage at the same time, there will also be odors due to the pressure difference. Toilet anti-overflow device, belongs to the flushing valve in the field of drainage, in order to provide a toilet anti-overflow device, it contains a sleeve, and its structural point is that the sleeve is divided into two parts.
The device is installed between the porcelain ring and the manure pipe under the toilet seat, when it is discharged downward. When it stinks. The sleeve mouth is firmly blocked to prevent the flooding, and the effect is obvious, especially suitable for high-rise and multi-storey buildings.
Residents on the second and third floors. The toilet anti-overflow device comprises a sleeve, which is characterized in that the sleeve is divided into upper and lower parts, and the lower end of the upper sleeve is connected with the upper end of the lower sleeve, and is connected with the stop piece respectively by screws.
1. Before the installation of the toilet, check whether there is sediment, debris and other blockages in the sewage pipeline, whether the installation surface is level 2, determine the sewage pipe and draw a cross line 3, determine the sewage outlet of the toilet and draw a cross line 4, determine the installation position at the bottom of the toilet with an electric drill and bury the expansion screw 5, install a special sealing ring (i.e., steamed wax orchid or rubber orchid) at the sewage outlet of the toilet or circle glass glue (putty) or cement slurry cement and sand ratio 1:3 6. The toilet crosshairs and the surface crosshairs are quasi-consistent, and the bottom of the toilet is circled, glass, glue (putty) or cement mortar, cement and sand ratio: 1:3, and the toilet installation should be kept horizontal; 7. Tighten the screws for the installation holes of the toilets; 8. Install and debug the water tank accessories, install and connect the water source, check whether the water inlet valve is inlet and sealed, check whether the drain valve and the installation position should be installed closely, whether the leakage check whether the button is closed, whether the chain is short, whether it is appropriate, whether the machine is jammed, check the leakage, install the water inlet valve filter device 9, If you find any differences in the trial process of adjusting the toilet, please refer to the toilet tank accessories to see the fault and treatment, check and deal with 10, the toilet installation should wait for the glass glue (putty) or cement slurry to solidify and discharge water, and use the curing room 24
You can only use the leather puff to suck, or use a professional dredging spring to dredge, I believe you don't have this thing, if the blockage is not bad, use the leather puff, if it is powerful, find a professional dredge phone in the corridor, call someone to help you, and the ultimate way, is to remove the toilet and then pass, is more troublesome.
The solution to the toilet tank not watering is as follows: 1. Close the angle valve first, remove the angle valve with a tool, and check whether the angle valve is rusty or scaled. >>>More
The solution to the toilet tank not watering is as follows: 1. Close the angle valve first, remove the angle valve with a tool, and check whether the angle valve is rusty or scaled. >>>More
Check the cause first, and then solve it. One is that water can enter, but the water level cannot rise, which is a problem with the flush valve; The second is that water cannot enter the water pipe, which is a problem with the water inlet valve. FYI.