What should I do if the toilet bowl has less water?

The initial decoration of the bathroom is very important, because the decoration at this time should take into account the problems of waterproof, odor prevention and so on. Many people find that soon after installing the toilet, it will smell, why?

This is what my toilet base looks like after it is disassembled, it has been smelly for three years, so disgusting.

Let's talk about the four main reasons why the toilet stinks:

1. The quality of the toilet product itself is poor, and the void of the toilet is large, and there are a lot of stains left in it.

2. The project was not done well during installation, and the flange ring under the toilet was not sealed.

3. The base of the toilet is not sealed, or the glass glue of the base is not done.

4. There are some firing holes in the toilet base, but these holes are not sealed, and the smell comes out.

The solution of Article 1 is that we can only buy toilet products with better quality, and we can buy better glazed products.

Article 2 suggests that you should use glass glue for the flange, and when you use this kind of glue, you should use water to flush it with water to see if there is any leakage.

Article 3 Most of the toilets that we sleep on now do not use cement to seal the bottom, most of them use glass glue, and we must pay attention to not break it when playing glass glue, and we must play it completely in a whole circle.

The base of the fourth toilet bowl usually has two or three firing holes, and many people don't know about it. Some merchants do not treat the product when it leaves the factory, so after you install it, the smell of the toilet will flow out of the holes here, so we have to seal these holes.

This small suggestion, in fact, installing a toilet is a kind of technical work, even if the worker is skilled, it is not as good as installing it yourself. When you buy a product, you can also let the merchant package install it, so that you can save the installation fee.

It should be noted that if you want to lay the floor tiles and then install the toilet, this is the correct installation sequence.

Generally, the toilet does not drain because the outlet at the bottom is not aligned with the drain, and the screws at the bottom of the toilet bowl are broken, which will cause the toilet to drain through, or the toilet has been used for a long time, and it will scale on the inner wall, and in serious cases, it will block the vent of the toilet bowl and cause the toilet to drain slowly, and it is also possible that the cement or tile fragments fall into it during decoration or will affect the drainage.

1. Check the water level of the toilet tank.

The main reason why the toilet flushes out at the push of a button is because there is a proper water source in the tank. However, when the water level in the toilet tank does not reach the range from the top of the overflow pipe, it means that the water level in the tank is low, so it is necessary to bend the floating arm in the tank upwards to allow more water to enter the tank and raise the water level.

2. Check the flush valve seat of the water tank.

If there is no problem with the proper water level in the tank, but the water output of the toilet is still too small to flush the toilet, it may be a problem with the ball plug on the flush valve seat of the tank. Because the position of the ball plug guide on the flush valve seat of the water tank is too low, the ball plug is too fast in the falling process, resulting in the failure to fall into the opening of the valve seat normally, so at this time, it is only necessary to raise the guide device to ensure that the ball plug and the steel rope are in a straight line.

Note: The guide must be aligned with the steel rope, otherwise the ball plug of the water tank will not fall into the opening of the valve seat correctly when it falls vertically, which will cause the toilet to flow non-stop!

3. Check the small holes in the edge of the toilet.

There are a circle of small holes under the edge of the toilet barrel, which are not usually noticed, but if these small holes are blocked by chemical residues in the water, it will also lead to the problem of low water output. Removing any clogs from the holes at the edge of the toilet bowl is relatively simple by using a small mirror to inspect the holes and then using a wire hanger or Phillips screwdriver to remove the clogged chemical residue.

There are many ways to repair a flush toilet, first of all, you need to find out the key point of the problem, for the fault of the toilet with less water output, the above three methods can solve the problem of too little toilet water output. Of course, in addition to these 3 problems that will cause less water output, there are other problems that can also cause this situation, so it is necessary to check and eliminate it a little bit, and then solve the problem in a targeted manner.

The amount of water out of the toilet is determined by the amount of water stored in the tank, and the amount of water stored is controlled by the liquid level rotation control valve or float rod angle in the tank, to see which one your toilet is, it is enough to rotate the regulating valve properly or raise the float rod angle.