What to pay attention to in the construction of light steel keel ceiling

1. The ceiling installation spacing and connection method of booms and keels should meet the design requirements, and the metal booms, keels and rear embedded parts should be treated with anti-corrosion or anti-rust.

2. The nail head exposed on the gypsum board should be dotted with anti-rust paint.

3. Wooden booms, wooden keels, modeling planks and wooden finishing materials should be treated with anti-corrosion, fire prevention and moth-proofing.

How to suspend the ceiling in the bedroom.

1. Wooden beams are used as ceilings to increase the sense of spatial hierarchy. Since it is impossible to eliminate the exposed beam, what we can do is use its properties to beautify it. If the beams are wide, deep and prominent, then for the overall aesthetics of the bedroom, the designer will usually cap one side along the beams.

But for a space with enough space, a simple decoration on it is sufficient. The spire space shown in the picture is covered with a slender locust, and its ceiling is deliberately installed with a gap of wood beams as decoration, which well reduces the excessive sense of emptiness of the bedroom space. Since the beams are wide and deep, it is easy to enhance the sense of hierarchy in the space.

2. Circumference gypsum line to create a false ceiling. At this time, the small apartment can be made of geometry, flowers, birds, insects and fish patterns with gypsum on the ceiling, which not only does not waste the floor height, but also gives the ceiling a multi-level expression. Of course, if the space is too small, there will definitely not be much ceiling to display, so it is better to honestly make a simple plaster line around the ceiling.

In this way, while invisibly increasing the space, Wuyou can also make the ceiling not monotonous, and under the cover of the light, it can also save some face for you.

3. The wall and the ceiling are matched to meet the visual needs. Generally speaking, the small apartment area is not large, the floor height is low, and it is not suitable for the ceiling, if it is a super mini small bedroom, it is not recommended to do a complex ceiling. Of course, if you really want to do it, you can also use the wall to match the ceiling to meet the visual needs.

The pure white cement ceiling is monotonous, but the simple beams added to it are a perfect complement – they start from the glass partition wall and extend to the side of the window, and the whole beam sits nicely above the bed, leaving a bit of bump and depth on the open ceiling.

Springline: Use a level meter to copy out the horizontal points on each corner of the wall in the room and pop up the leveling line.

Fixed hanging rods: under normal circumstances, fixed hanging rods are fixed with expansion bolts to hang rods, not on the ceiling of people, the length of the boom is less than 1000, 6 booms can be used, then greater than 1000mm, then 8 booms should be used, and it should also be provided with reverse support.

Installation of side keel: when installing the side keel, it should be elastic according to the design requirements, and the L-shaped galvanized light steel strip should be fixed on the embedded wooden brick with self-tapping screws along the horizontal keel line on the wall, and the concrete wall (column) can be fixed with nails, and its spacing should not be greater than the spacing of the ceiling keel.

Install the main keel its spacing in 900 1000mm, should be hung on the boom, parallel installation in the long direction of the room, its span is greater than 15m above the ceiling, should be on the main keel, every 15m plus a large keel, and the vertical main keel welded firmly.

INSTALL THE SECONDARY KEEL: THE SECONDARY KEEL AND THE MAIN KEEL SHOULD BE CLOSE TOGETHER, AND ITS SPACING SHOULD BE 300 600MM, WHEN THE SECONDARY KEEL IS FIXED ON THE MAIN KEEL WITH A T-SHAPED GALVANIZED IRON SHEET CONNECTOR, THE TWO ENDS OF THE SECONDARY KEEL SHOULD BE ON THE HORIZONTAL FLANGE OF THE L-SHAPED SIDE KEEL.

Mounting cover panel: the long side of the gypsum board should be laid along the longitudinal secondary keel; The distance between the self-tapping screw and the edge of the gypsum board on the paper surface should be 10 15mm for the board edge wrapped with the face paper, and 15 20mm for the cutting edge of the board. The veneer should be fixed in a free state to avoid the phenomenon of bending edges and bulging.