-
Anonymous users2024-01-24Don't underestimate it for ceiling installation, its installation is still more sudden, so that the installed ceiling will be safer, so that we can rest assured that we can use it. (1) Operation method: mainly consider the connection of embedded parts and transition parts.
Embed iron or wood bricks in the structural layer (except for water brick load-bearing). The burial position should be accurate and there should be sufficient room for adjustment. Transition connectors are set on the iron parts and wooden bricks in order to adjust the error of the parts, and can be nailed, welded and screwed through with the parts.
The boom, sling and transition connector are connected. (2) How to install the chandelier in the living room is more suitable for installation precautions: If there are multiple chandeliers during installation, you should pay attention to their position and length, and install the chandelier at the same time as the ceiling, so that the position and height of the lamp can be adjusted based on the ceiling joist.
The boom out of the ceiling must be used by direct exit method and casing method. The addition of a pipe facilitates installation, and the chandelier keeps the ceiling panel intact and drills holes only where the outlet pipe is needed. The hanging cup directly out of the ceiling is not easy to align when the board surface is drilled during installation.
Sometimes the method of installing the boom first and then cutting the hole in the panel may be used, but it has an impact on the decorative effect. The boom should have a certain length of thread for adjusting the height. The light box is suspended under the sling boom, and the reliability of the connection should be noted.
(3) The boom, the sling and the joist are connected The boom and the sling are directly nailed and screwed on the secondary joist, or the above-mentioned plate surface perforation method is connected to the vertical run. Or hang on the cross joist that is added between the secondary pick-ups. The power of the light source used in the ceiling lamp:
Incandescent bulbs are 40 100W, and fluorescent lamps are mostly 30 40W.
-
Anonymous users2024-01-231. Prepare the installation tools.
If we want to install a ceiling light, we must first prepare the installers we need, such as: impact drills, electrician's pliers, screwdrivers, insulating tape, a small piece of wood, a wooden ladder, etc.
2. Determine the location of the ceiling light in the living room.
Before installing the ceiling lamp in the living room, you need to determine the installation location, which is generally installed in the center of the living room or above the coffee table. Straight incandescent or fluorescent lamps are usually installed in the front part of the cabinet, so that part of the light emitted by the lamp will be reflected to the backsplash and reflected to the worktop and to the center of the space.
3. Dismantle the ceiling lamp mask in the living room.
After the mask is removed, the lamp tube is also removed. In general, there are two ways to fix ceiling lamp masks: rotation and snap. When removing the mask of the ceiling light in the living room, care needs to be taken to prevent damage to the ceiling light in the living room.
4. Install the ceiling lamp base in the living room.
Thread the previously reserved wire into the wire hole of the base, hold the base of the ceiling lamp with one hand, fix it in the position to be installed, use a screwdriver to screw one of the screws into the empty position, note that it does not need to be tightened too tightly here, so that when the position is not found to be accurate later, it is convenient to move the position, adjust the position and place it correctly.
5. Connect the wires.
After we fix the base, we can connect the power cord with the wiring base of the ceiling lamp in the living room, pay attention to the two wires connected with the power cord of the ceiling lamp, the electrical contact should be good, for the safety of electricity in the future, we also need to wrap it with black tape respectively, and keep a certain distance.
6. Install the mask of the ceiling in the living room.
Mask installation is the final step in installing a ceiling light in your living room. Usually after connecting the wires, you can first try whether the lamp can be used normally, and after careful inspection, you can install the mask of the living room ceiling lamp, after the mask is installed, the installation process of the entire living room ceiling lamp also ends here.
The design of the ceiling is also diverse, and different materials and design types will bring different life feelings to the residents. Whether simple or complex, the design is created for a warm and quality life. The living room ceiling on the market is beautiful, beautiful and atmospheric, so the decorative effect in the living room is also different, then. >>>More
What is the height of your living room, the chandelier should be cautious, otherwise it will give people depression is generally 1 meter 9 to 2 meters, personal feeling.
Choosing a marble chandelier for living room lights is a good choice. The marble chandelier has a delicate texture, uniform light transmission, and expresses emotions with the purest color, a style of blending Chinese and Western, ancient and modern. Each marble lamp is expensive, carefully appreciated, people feel that time and space are infinitely expanded, and the light of personality is dazzling and crystalline. >>>More
The chandelier in the living room is made of all-copper marble lamp, which is high-end and high-grade, and the installation is simple and worry-free.
Before the ceiling, consider the installation location of the lamp and take measures. Now you can only choose a chandelier with light weight as much as possible, and look for a position with a keel to fix the chandelier. >>>More