How to adjust the toilet bowl with a small amount of water?

First of all, we lift the lid of the toilet, pay attention to be sure to hold it steady, handle it gently, and do not bump it.

We see that there are two black columns on the toilet lid, this is the toilet water connecting rod, this can be adjusted to control the strength of the toilet button, this should not be adjusted too long, so that the lid can just touch the blue and yellow blocks below.

If the water level is higher than the overflow pipe, then we adjust the position of the float on the left, rotate the white rod in the circle, which can be used to adjust the high and low position of the float, after rotating a few times, release part of the water, and then observe the water level after the water storage stops until it reaches the satisfactory position.

At the same time, we also see that in front of this water button, there is a yellow block that can be moved up and down, this is used to adjust the toilet drainage, if you feel that the toilet button is pressed once, the drainage is too large or too small, you can adjust the height of this small yellow block, so as to achieve a satisfactory drainage.

The above is the method of adjusting the water storage level and primary discharge of the toilet.

1. Place bricks or drink bottles in the toilet tank to increase the amount of water.

2. Control the flushing volume of the toilet by controlling the float handle inside the toilet tank.

Third, the toilet suction power is not enough. The mouth of the sewage pipe is not tightly sealed, and the toilet is reinstalled. To install a new flange ring from the base of the toilet, and then seal it with glass glue to make a good sealing effect.

First of all, we must know that the adjustment of the total water inlet of the water tank is the height of the float on the left inlet valve. Then you should ask the question of the displacement of the drain valve, first of all, you must recognize the role of the two movable adjustment joints on the drain valve, as shown in the following figure

> full drainage should be the ceramic water tank cover of the two buttons in the large area (depending on the plumber assembly situation is different, there is also a small installation area under the one, it is not easy to say) the correspondence, the most direct way to judge is to press the depth of a little deeper that is the full drainage button, the general is as shown in the white representation.

Then the most important thing is to talk about the two blue and red adjustment buttons shown in the figure up and down to adjust the water output, the general rule is less up and down more, that is, if you want to have the largest water output of full drainage and semi-drainage, adjust the two buttons to the bottom, of course, the expert's suggestion is that the full drainage should be adjusted to the bottom as well, because the full drainage is generally used to flush the stool, of course, the larger the water volume, the more smooth and thorough; The semi-drained one is used to flush urine, and the general one does not need a large amount of water, so it is appropriate to adjust it to the middle position. Well, that's it.

Open the upper lid of the toilet, there are two buttons on the lid of the water tank, one is a small amount of water, the other is a large amount of water, the water tank of the toilet is generally a general rule is less up and down more, if you want the water output of full drainage and semi-drainage is the largest, just adjust the two buttons to the bottom, and the full drainage should be adjusted to the bottom, because the full drainage is generally used to flush the stool, and the larger the amount of water, the better. Semi-draining is used for urinating, and generally does not need to use a large amount of water, so it is appropriate to adjust it to the middle position.

Open the toilet lid and adjust the buoy upwards.

What kind of toilet are you talking about? Now there are single-row floats and double-gear pendants. It is not recommended to get it yourself, find after-sales service, and the amount of water may be too much if you adjust it yourself, and it will affect the function.

The lid is removed, and the water polo is adjusted upwards.

1.Water tank type: There is a toilet with a water tank at the rear, when flushing, the water always feels weak, and the water volume in the water tank can be improved by adjusting the water level. As for the back of the toilet, there is a switch to adjust the amount of water in the water tank, regardless of the flushing force.

2.Pressure: It flushes when pressed by the wrench (there is no water tank at the back of the toilet), but it is not"There is a switch at the back of the toilet that can be turned with a vise"。

Instead, there is a screw with a circular slotted hole threaded hole on the adapter next to the pipeline next to the pressure spring barrel (the same as the shower head and the wall elbow to adjust the size of the water outlet), and turning to the right with a slotted driver will cause a large amount of water to flush.