How to tighten the toilet seat when it is loose

If the toilet lid is loose, first of all, the toilet lid should be uncovered, find the screw cap at the connection between the toilet lid and the toilet, usually on both sides of the connection, and tighten it directly after finding the screw cap, or you can tighten the screws with a special screwdriver, if you can't handle it well, you can also ask a professional to tighten the toilet cover, or buy a new toilet cover.

> different toilet brands, the position of the screw cap on the toilet lid is not the same, you can first uncover the toilet lid and find the screw cap at the connection between the toilet lid and the toilet, usually on both sides of the connection, you can tighten it directly by hand, or you can tighten the screws with a special screwdriver.

> if you feel that the toilet is too dirty in the process of tightening the toilet lid, you can also bring gloves and other tools to tighten the screw cap.

> when the screws of the toilet seat are broken and there are no screws, you can go to the market to find the corresponding screws, or you can find the screws required by the merchant who originally bought the toilet, but you can't find the screws of the toilet seat, so you can only buy a new toilet seat similar to the old toilet seat.

<>First of all, we need to close the toilet lid, and when the toilet lid is closed, you will find that there is a screw casing on the back of the toilet lid. Gently remove the cover of the screw housing, and the screws will be visible. Then we tighten the screws under the screw housing, and then cover the cover of the screw housing on the screws, after all this is done, lift the toilet lid again, confirm whether the screws of the toilet seat have been tightened, if you have not received the appropriate tightness, you can also adjust it again.

1. You need to wipe the toilet lid clean with a damp rag, and you must do a good job of hygiene and cleaning. Then put the purchased screws away from use.

2. Then look down and look for it, under the toilet test, there is a nut to fix the screw of the toilet seat, and stack it manually.

3. After the nuts are stacked, gently remove the toilet lid and remove the remaining or damaged screws and screw slots.

4. Install the newly bought toilet seat screw card slot.

The metal one is the screw, which is fixed to the inside of the wall, and as long as it doesn't get pulled out, it's fine. The plastic sheet should be a gasket, which is used to separate the toilet from the wall.

In this case, there should be a nut that is screwed on that screw. If you can't find a nut, go get one. If you want stainless steel, 1-2 pieces a maximum of one.

1. When replacing the toilet cover, you only need to remove the fixing bolt at the back of the toilet to replace it, and you can operate it in the opposite direction during installation. Most toilet seats are large and small, and adjusting the two bolts during installation is a no-brainer.

2. But you also need to measure the size, the distance between the screw holes, the width and length of the toilet seat, and then buy a new toilet cover to replace! To install the toilet seat, you need to remove the fixing bolts at the back of the toilet, remove the previous toilet cover, and then replace the new toilet seat with a fixed screw cap.

3. Go around the toilet bowl to see where the screw cap of the toilet lid is, then choose a suitable wrench, just take off the screw cap, and then replace it with a new one.

4. Generally, the position of the screw cap is not easy to find the potato vertical, some are in the light, and some are in the dark. In the dark place of the screw cap, inside the toilet bowl against the side of the tank, open the lid. If you put your hand in it and touch it upwards and in the direction of the tank, you should be able to touch it, but you can't see it.

Find the screw cap, remove it with a live handler, and replace it with a new one. Generally, the position of the screw cap is not easy to find, some are in the light, and some are in the dark. In the dark place of the screw cap, inside the toilet bowl against the side of the tank, open the lid.

If you put your hand in it and touch it upwards and in the direction of the tank, you should be able to touch it, but you can't see it.

5. We should note that most toilet seats are regardless of size, and the installation difference can be adjusted to two bolts. However, it is also necessary to measure the size, the distance between the screw holes, the width and length of the toilet seat, and then buy a new toilet seat to replace it.