How to go to the bathroom decoration water pipe

How to lay toilet pipes? The installation method of bathroom water pipes should be scientific and reasonable in order not to cause problems, and reasonable steps must be followed. Now let's introduce you to the three steps of laying water pipes in the bathroom.

1. Before laying the toilet water pipe.

Bathroom water pipes need to choose the right water pipe before installation, there are many types of water pipes on the market, such as PPR water pipes, copper pipes, aluminum-plastic pipes, stainless steel pipes, etc., a variety of different materials of water pipes have their characteristics, PPR pipes as a new type of water pipe materials, non-toxic, light weight, pressure resistance, corrosion resistance, once the installation pressure test passes, will never leak, so most people will choose PPR water pipes.

2. When the toilet water pipe is laid.

When the bathroom water pipe is installed, it is necessary to discuss with the installation master the specific direction of the waterway, and follow the principle that it is best to go to the top and not to the ground, and to be hot and cold. After the water pipe is laid, before sealing the groove, it should be fixed with a pipe clamp, and the spacing between the cold water pipe clamps is not more than 60 cm, and the spacing of the hot water pipe clamps is not more than 25 cm.

3. When the toilet water pipe is laid.

After the toilet water pipe is laid and installed, the pipe head should be plugged immediately with a pipe plug to avoid debris falling in, and then a pressure test is carried out to detect whether the installed water pipe has water seepage or leakage. Although there is no pressure in the sewer pipe, it is also necessary to check the water and carefully check whether there is any leakage or water seepage.

After reading the above three installation steps, do you have a certain understanding of how to lay water pipes in the bathroom? Reasonable and correct installation can make the bathroom in the home can be used normally for a long time, and a small water pipe is also very important. Finally, it is worth mentioning that no matter how the bathroom decoration is, it is necessary for us to understand the common sense of bathroom decoration.

I think that in order to effectively implement the precautions for bathroom decoration, we must have some toilet safety knowledge, so as to avoid accidents that should not occur.

1. The hot and cold water pipes of the bathroom water pipes should be separated, and the distance should not be too close. The height of the shower water pipe is between.

2. For the installation of toilet water pipes, the general water pipes go to the top and do not go to the ground, the cold and hot water outlets must be horizontal, generally hot on the left and cool on the right, the pipeline laying needs to be horizontal and straight, and the layout direction should be safe and reasonable. The position of the pipe clamp and the slope of the pipe should meet the requirements of the specification. All kinds of valves should be installed in the correct and flat position, which is easy to use and maintain.

3. The cold and hot water pipes are all into the wall, and the depth of the tank needs to be checked when slotting, and the cold and hot water pipes cannot be the same tank.

4. When installing the water inlet and outlet of the water heater, the valve of the water inlet and the valve of the air inlet must be considered and installed in the corresponding position.

How to go to the bathroom water pipe - introduction to the precautions for the installation of the bathroom water pipe.

When installing the toilet water pipe, first consider the layout of the bathroom, combined with the sewer position (because the sewer position is generally not moving, if it is very troublesome, it is necessary to increase the height of the ground by not less than 10 cm (cm) to add an elbow to the sewer on the sewer, which generally affects the flushing effect, so it is not recommended to change the sewer), according to the facilities in the bathroom, arrange the location of the water pipe. Then groove the wall, bury the upper water pipe into the wall and plaster, and paste the tile outside. The distance between the hot and cold water holes in the washbasin is generally 10 cm, hot on the left and cold on the right; The hot and cold water holes are generally 15 cm in the bath, hot on the left and cold on the right.

Toilets, mop sinks, washing machines, etc. do not need hot water holes. When designing the water pipe, you should consider the location of the faucet installation of the washing machine and the arrangement of the sewer. At the same time, pay attention to whether the location of the power outlet is appropriate.

When placing a drum washing machine in the kitchen cabinet, be sure to determine the size of the washing machine and kitchen cabinet, so as to leave a good position for loading and unloading water.

The key to the problem of how to go to the bathroom water pipe is to look at the design of the family, and the design of the waterway should be carried out according to the spatial layout and size of the bathroom. The design of the toilet water pipe is more important, if the design is not reasonable, it is easy to overflow the water pipe and block the water pipe in the future.

Let's be more detailed, do you have a simple drawing? Or describe in words what was the original location and how it was going to be changed?

When <> bathroom decoration and installation of water pipes, the first thing to consider is the layout of the bathroom, combined with the location of the sewer, and the location of the water pipes installed according to the facilities in the bathroom. Then groove the wall, bury the water pipe in the wall, plaster, and paste the tile outside. The distance between the hot and cold water holes is usually 10 centimeters from the washing area, with the left side hot and the right side cold.

Hot and cold water holes are usually fifteen centimeters in the bath, hot on the left and cold on the right. Mop sinks, washing machines, toilets, etc., do not need to be equipped with hot water holes. How to go to the bathroom water pipe, it still depends on the design of the house, according to the space layout and size of the bathroom.