-
Anonymous users2024-01-24Step 1 Before the toilet is installed, a comprehensive inspection of the sewage pipe should be carried out to see if there is any mud, sand, waste paper and other debris in the pipe.
At the same time, it should also be checked whether the ground of the toilet installation position is horizontal, and if the ground is found to be uneven, the ground should be leveled.
Step 2 Flip the toilet bowl and determine the center on the toilet drain.
At the same time, draw a cross centerline, which should extend to the bottom of the toilet bowl around the feet.
Step 3 Align the reticle line on the toilet bowl with the ground drain outlet and install the toilet bowl horizontally.
At the same time, press the sealing ring tightly and install the anchor screws and decorative caps.
Step 4 Install a special sealing ring on the toilet drain.
Step 5 Drain the water for 3-5 minutes to rinse the pipes to ensure the cleanliness of the water pipes.
Then install the angle valve and connecting hose.
Then connect the hose with the installed tank fitting inlet valve and press the water source.
Step 6 Check whether the water inlet and sealing of the water inlet valve are normal.
Check whether the installation position of the drain valve is flexible, whether there is jamming and leakage, and whether there is leakage to install the filter device of the inlet valve.
-
Anonymous users2024-01-231. Bathroom decoration toilet installation process - punching.
After determining the installation position of the toilet, align the bottom sewage outlet of the toilet with the ground sewage nozzle, and then draw the position of the fixed hole at the bottom corner of the toilet on the ground according to the peripheral size of the toilet base, and punch the hole with a percussion drill, the general hole depth is about 5cm.
2. Bathroom decoration toilet installation process - toilet positioning.
After the eyelet is laid, hammer the steel expansion bolt into the eyelet, put it into the bottom corner of the toilet, and tighten the nut to position the toilet. Note: The toilet drain should be tightly connected to the toilet floor drain pipe and need to be sealed.
3. Bathroom decoration toilet installation process - fixed toilet.
According to the height of the purchased toilet tank and the position of the eyelet on the back wall of the water tank, find the fixed position of the toilet on the wall to punch the hole, and then knock the steel expansion bolt into the hole, the water tank is in place, make the back wall eyelet into the expansion bolt, add a 3mm thick nylon washer and put the nut on it and tighten it. (In the case of a one-piece flush toilet, this step can be omitted.) )
4. Bathroom decoration toilet installation process - connecting pipe installation.
After the water tank is installed, you can start to install the connecting pipe between the water tank and the base of the flush toilet, and the connecting pipe between the water inlet pipe and the bottom of the water tank for water supply. Remember, you need to install an angle valve at the connection of the inlet pipe, that is, a control valve!
5. Bathroom decoration toilet installation process - accessories installation.
Install the floats, water scoops and other accessories in the water tank.
6. Bathroom decoration toilet installation process - detect the size of the water spray.
After the fittings in the tank are installed, they need to be tested. Open the water inlet valve, observe the height of the water required in the water tank, adjust the height of the float water scoop, and adjust the tightness of its control screws according to the size of the water spray valve.
7. Bathroom decoration toilet installation process - detect the sewage effect.
After completing the inspection of the fittings in the water tank, you can check the sewage effect of the toilet bowl and whether there is any leakage in the connection between the pipes.
8. Bathroom decoration toilet installation process - sealing work.
Once the test is complete and everything is correct, the gap between the toilet base and the floor can be sealed with a material such as putty or silicone. (Note: Cement slurry, cement mortar, etc. cannot be used as sealing materials here!) )
9. Bathroom decoration toilet installation process - install the seat ring and toilet cover.
Install the seat and toilet lid of the flush toilet. At this point, the flush toilet is installed.
1.Wipe the drain at the bottom of the toilet and the drain on the floor around the tear-covered drain, and ensure that there is no moisture attached during installation. >>>More
Toilet seal installation Be sure to close the toilet inlet valve. You can turn off the water valve at the toilet, but you may also need to go to the line level or basement to turn off the water. >>>More
Summary. Hello! I have received your question, I am helping you sort out the relevant information, it will take some time to type, I will reply to you immediately, please wait a while! Thank you. >>>More
Toilet flange installation method:
You can replace the toilet seal under the toilet bowl by yourself, also called the toilet flange, instead of waiting for a plumber to repair it, which will not only save time, but also avoid the inconvenience of using it as soon as possible. If you hire a toilet repairer, many toilet repairers are not so careful, and the quality of the toilet flange they provide may not be good. In fact, it is not difficult at all, you only need to know a little knowledge, follow a few very simple steps to install a toilet seal at home, which is cheap and can solve the problem of toilet leakage and avoid more losses. >>>More
Use a wallpaper knife to dissolve the glass glue and other objects around the toilet, you can remove it directly, and then see how the flange is, if it has been damaged, replace it with a new one, put down the new toilet by aiming at the drain, and then hit the glass glue to seal the ground for 24 hours without sticking water!