Is there rebar in the cement bars on the balcony? Just about a meter high low wall of cement bricks

When laying bricks, two 6 mm steel bars should be driven into the junction of the barrier and the load-bearing wall to play a tensile role (the height is 5OCm two, the length depends on the situation), and the top of the barrier needs to be poured with cement concrete and the thickness is between 12 and 15cm.

I am a construction company, you should use four eight-centimeter steel bars at each of the two corners of the balcony to pound the cement, and after the bricks are finished, use four long six-centimeter steel bars from both sides of the balcony to pave from the top of the balcony wall, and tie each other with the steel bars reserved on the previous two columns, and then use wooden boards to make molds and pound the cement on the surface.

If the thickness is within 10 centimeters, if it is 15 centimeters, it may be brick-based, at most one layer above.

It can be changed.

We now have railings and brick masonry on the balcony of the building on this construction site 1, I don't know whether the balcony on both sides of your balcony is a wall or a column, it is best to chisel a stucco layer to see, if it is a brick wall, it is best not to punch holes on both sides of the planting bar, so the planting bar is not firm, but you can do four structural columns at the edge of the balcony (that is, the position of the iron railing) (depending on the width of your balcony to decide whether it is four or three), and then insert Rachel bars from the structural columns, which is more firm. If the two sides are concrete structures, it is good to plant steel bars directly on both sides, and it is best to do it yourself to be better, it is best to pull through the steel bars on both sides (that is, when laying bricks, put two usual steel bars every 400mm high, and connect them with the steel bars planted on the concrete structure on both sides).Personally, I think it is more appropriate to make a 1200mm balcony.

When the bricks are built to 1100 or 1150mm high, do not build them again, and pour the above several minutes of height directly with concrete (of course, two usual steel bars should be placed inside).

2. Considering that the balcony railing needs to have a waterproof function, the bricks for masonry are best made of solid bricks, such as clay solid bricks (this kind of brick is not used in the building now, I don't know if you can buy it there, don't worry that the floor slab can't bear such a heavy load, the design institute design drawings are at least more than 200% of the actual use of the load to design), and there are concrete solid bricks, ninety-five bricks (length of 240mm) or eight-five bricks (length of 200mm) can be

DOWNSTAIRS: THE AVERAGE FAMILY MOTORCYCLE HAS A TOP SPEED OF 180 OR 200 H/H ON THE DIAL, BUT CAN IT RUN THAT FAST? What is the use of the meter according to your meaning?

Take it away or you go to sue the manufacturer for exaggeration, it's not true, and you can still make some money to use It's okay Don't come to blindly participate, if you don't understand, learn to be humble

Generally, balconies of formal design and construction should be able to be replaced with brick railings. IT SHOULD BE NOTED THAT LIGHTWEIGHT BRICKS SHOULD BE USED AS MUCH AS POSSIBLE, AND THE THICKNESS OF THE WALL SHOULD NOT EXCEED 120MM; The end of the balcony is provided with two small structural columns, drilled and inserted steel bars, and the wall is retained for reinforcement, and the first masonry is followed by pouring; Clean the bottom before laying bricks, and consider chiseling.

You can not add it, but you must use some mortar, and make it full of mortar to ensure that the bricks do not fall off!

There are steel bars, and the answer to the supplementary upstairs is that after you build the bricks, there will be an increase in pressure at the ends of the beams on both sides of the lower part of the balcony slab, and it is best to consider the bearing capacity of the beams in masonry, don't mess around, safety first.

If the quality is good, you should put steel bars. Safety is the most important thing, so stay safe.

There is no need, if you want to add reinforcement, you must do concrete cast-in-situ to play the role of force, otherwise it is useless.

The design institute upstairs designed the drawings at least more than 200% of the actual used load) Who said this?

Then do you still need a design institute to do it?

A direct estimate will do.