What accessories do you need to install a toilet? How to install

"Flush toilet fittings installation step 1, determine the installation location, and drill a hole in the ground. After aligning the ground sewage nozzle with the sewage outlet at the bottom of the flush toilet, according to the peripheral size of the toilet base, draw the position of the fixed hole at the bottom corner of the toilet on the ground, and punch the hole with a percussion drill. The depth of the eyelets is about 5 cm.

2. Install the toilet base. Hammer the steel expansion bolt into the ground drill, put the expansion bolt into the bottom corner of the toilet bowl and tighten the nut to put the toilet in place. The toilet drain outlet should be tightly connected with the preset sewage pipe on the ground and sealed.

3. Install the water tank (the one-piece toilet does not need this step) according to the installation height of the water tank and the position of the hole on the back wall of the water tank, drill the hole in the corresponding fixed position on the wall and knock in the steel expansion bolt, and then put the water tank in place, make the rear wall eyelet into the expansion bolt, add a 3 mm thick nylon washer and put the nut on it and tighten it. 4. Install the connecting pipe between the water tank and the toilet base (with copper pipe or plastic pipe, etc.), and the connecting pipe between the water inlet pipe and the bottom of the water tank (with stainless steel bellows, etc.). Angle valves (water inlet control valves) should be installed at the connection of the water inlet pipe.

5. Install the float and other accessories in the water tank. 6. After opening the water inlet valve, adjust the floating height of the float according to the required water inlet height in the water tank, and adjust the tightness of the control screw according to the size of the water spray of the water spray valve. 7. 8. Seal the gap between the toilet base and the ground with putty or silicone.

Cement slurry or cement mortar shall not be used as sealing materials. 9. Install the toilet seat and toilet lid. "

If you really need to install it yourself, or ask a plumber craftsman to install it, you need to prepare the following materials: 1. Glass glue. It is recommended to use white glass glue instead of transparent ones.

Because after using transparent glass glue for a period of time, the enzyme will turn black due to moisture and dirty, which will seriously affect the sound of the branches. 2. a hose. It is recommended to use good quality hose fittings, which will be more worry-free.

If you use a hose that is not of good quality, water leakage will occur, and it will need to be repaired and replaced, which is more troublesome. After the replacement, there is no longer water leakage, which is relatively worry-free. If the water leaks into the wall, or if there is a flood, it will affect the decoration of the home and the decoration downstairs, because of a small loss.

3. Raw tape. It is used to connect the hose to the water inlet pipe. Tools to prepare for the stove shed:

1. Glass gun. This is something that most plumbers will bring their own. 2. Active wrench.

It is used when connecting the hose to the water inlet pipe. 3. Utility knife. Use when cutting raw tape.

You can tear it without a knife, and you can tear it with your hands, just use force. That's basically it. "

1. Glass glue. It is recommended to use white glass glue instead of transparent ones. Because after using transparent glass glue for a period of time, the enzyme will turn black due to moisture and dirty, which will seriously affect the appearance.

2. It is recommended to use good quality hose fittings, which will be more worry-free. If you use a hose that is not of good quality, water leakage will occur, and it will need to be repaired and replaced, which is more troublesome. After the replacement, there is no longer water leakage, which is relatively worry-free.

If the water leaks into the wall, or if there is a flood, it will affect the decoration of the home and the repair downstairs, because of the small loss. 3. Raw tape. It is used to connect the hose to the water inlet pipe.

Tools to prepare: 1. Glass gun. This is something that most plumbers will bring their own.

2. Active wrench. It is used to connect the hose to the water inlet pipe. 3. Utility knife.

Use when cutting raw tape. You can tear it without a knife, and you can tear it with your hands, just use force. That's basically it.