-
1. First of all, it is necessary to find out the water leakage point, and prescribe the right medicine according to the leakage situation.
2. If the tile has cracks and leaks, then we can use a professional caulk to refill the gap. After the caulk is dry, apply a waterproof layer, so that you can avoid the need to break the floor to repair the problem.
3. In the case that the water pipe is not broken, the dust, oil, stagnant water and so on on the surface can be cleaned to maintain the dryness of the ground, such as the tile joint is filled with caulk, you need to use a knife to draw a small groove, the tile joint, wall joint and other parts are sprayed with penetrating waterproofing agent, sprayed evenly, and when it is almost dry, fill the defective part with caulking paste.
Precautions. Note: After the waterproofing construction is completed, the waterproof material is required to be dry (usually after 24 hours) before it can be drenched.
-
Maybe the slope of the bathroom floor is too small, causing water to accumulate, but if the slope is reasonable, the water should flow into the floor drain, and without the water will not seep.
-
It's best to smash it, and do it all over again. If you don't want to smash it, you can find the leakage point, and then take the water to make up the gaps in the tiles without leaking, and then use waterproofing agent to brush both sides to keep them straight.
-
First of all, if there is water seepage, dampness, peeling and other situations in the bathroom, then it is generally caused by water leakage in the bathroom. The most important thing now is to find the cause of the leak
1. Find a professional hydropower worker to check whether the pipeline is ruptured and causes water leakage, etc., if it is a pipeline problem, it is necessary to repair the pipeline in time to solve the water leakage problem;
2. If there is no problem with the pipeline, then consider that the waterproof layer is not done well and cause water leakage, if the local water leakage is serious, it is recommended to do the waterproofing again, so as to fundamentally solve the problem.
Secondly, more than 80% of the leakage in the bathroom is concentrated in the yin and yang corners, pipes, sanitary ware, floor drains and other places, so it is recommended to use kitchen and bathroom waterproof slurry when doing waterproofing, first repair and strengthen these permeable parts, and then do waterproofing as a whole, so that the waterproof effect is better. However, remember to carry out standard construction according to the requirements during construction, so as to ensure a good waterproof effect.
Finally, I would like to add that whether it is a partial repair or a complete re-waterproofing, it is unrealistic not to smash the floor, and it is impossible to fundamentally solve the problem, so it is recommended to smash a part of the floor according to the actual situation.
-
It is necessary to smash the bricks, reapply them with a dust-repellent paint, and then lift them on the floor.
-
If it is still leaking after simple repairs, affecting the downstairs, and there is a dispute for a long time, then hurry up, find a worker, and smash it to renovate it.
-
If the dew point is in the floor cushion, the floor needs to be smashed.
-
It is necessary to determine whether the pipe inside the wall is leaking or the leakage is caused by waterproofing. If the water is waterproof and leaking, you should knock off the floor tiles and redo the waterproofing, and do a closed water experiment.
-
It depends on how far the leakage is, if it is not serious, find the leak and fill it, if it is serious, then you have to do it from scratch.
-
No, the general water pipe cannot be damaged inside the wall, but only the exposed interface is damaged, and there is no need to smash the floor.
-
No, you can use the plugging king and 902 glue.
-
The bathroom floor should be re-smashed to make it waterproof.
-
Remove all the floor tiles and cement sand in the bathroom, and then do waterproofing and use floor tiles.
-
No need to smash bricks! Now there is a waterproof, brush directly on the surface of the tile! I used it in Beijing.
-
If you want to deal with it well, you must smash the floor tiles, please adopt, do the task, thank you.
-
Smash it open and redo it waterproof. Or inspect the pipeline.
-
If the commode is leaking, use waterproof glue.
-
No need to smash, just use a leak preventer.
-
If you need to be sinned, it is better to find a professional.
You should be describing the situation of water seepage in the bathroom and the bathroom partition room, so you need to find the cause of the water seepage first >>>More
: First check that part (to.
Downstairs looks at that place) leaks. >>>More
Contact the property in your neighborhood first to determine who is responsible. >>>More
If the upstairs cannot be coordinated, it is necessary to make the square ceiling into a funnel type to drain the dirty water to the sewer, and the whole fan to exhaust the odor to the outside.
Leaking water in the bathroom, leaking or leaking downstairs is a troublesome thing in life, which makes many people very annoyed. Now I would like to introduce to you the experience I have accumulated over the years, so that you can easily judge how to deal with it. >>>More