What do you need to pay attention to when installing a bathroom faucet

1.Before installation, it should be confirmed that there is no sand hole on the surface of the product, the wall thickness of the threaded pipe is uniform, and the switch rotates flexibly. Before installation, the water pipe should be dredged once to confirm that there is no garbage and residue in the water pipe, so as not to affect the water flow.

2.Pay attention to the winding direction, taking the angle valve as an example, when the angle valve is screwed into the inner wire thread in the wall, it rotates clockwise to the right, then the direction in which we wrap the leftover tape on the angle valve is to the left counterclockwise, so that when the angle valve is tightened, it will be tighter and tighter, and it will not loosen.

3.When winding, tighten the raw material belt, so that the raw material belt is tightly attached to the thread, as tight as possible, do not loosen the winding, and press it tightly by hand after wrapping, or you can wrap it while pressing.

4.As for the winding "several layers", there is no hard and fast rule, which can be tightened and does not leak, but according to experience, it is usually necessary to wind more than a dozen times to ensure the sealing effect.

5.Don't screw the thread to death, by a little force, it doesn't necessarily have to be screwed to the real twist to not leak, as long as the feel can eat when screwing. Also, pay attention to the depth of screwing in.

Precautions for installing angle valves.

1.The place where the angle valve faucet should be wound with raw material is less: it feels like it is about the same after three or five turns, but the result is always leaking.

2.When installing the angle valve faucet, the place where the raw material belt should not be wrapped violently: the place where the hose is wired, the two ends of the shower hose, etc., the more it is wrapped, the more it will leak.

3.The leak test is not careful: there is no leakage at that time, and then you have to observe it a few more times, the water is fine, the gas should be especially noted, and the gas pipeline should be brushed with soapy water on the connectors and joints, and the foaming should be dealt with in time.

4.Hoses (braided hoses and corrugated hoses) are not naturally bent by force: the hose can not be bent within 5 cm from the hose joint, can not be bent to death, can not be in a constant state of stress, etc., the life of the hose will be greatly reduced under these sick conditions.

For bathroom faucets, it is not recommended to use pull-out faucets. Unless your washbasin is far from the front and back. If you choose a faucet, it is recommended to use a high-quality export OEM brand, such as BSBRIDGE.

It must be of high quality, otherwise it will corrode and oxidize and leak.

1. Before installing the faucet, it is necessary to flush with water, wash the sediment impurities in the water pipe, remove the debris in the installation hole, and check that the accessories in the packaging box are not mixed with impurities, so as not to block or wear the ceramic valve core.

2. Use a metal hose to connect the water pipe, you don't need to consider the installation position of the water pipe, but it should be noted that the length of the hose is usually 30cm (import size, individual brands or hard pipes), and if you connect the water pipe with a metal hard pipe, you should buy the faucet first, and then lay the water pipe according to the length and size of the faucet hard pipe, of course, in terms of service life, the hard pipe is better than the hose, and in the same way, when installing the sink faucet, if the water pipe is laid above the sink, it is best to install the in-wall sink faucet. Otherwise, install a regular sink faucet.

3. The requirements for the relevant accessories of imported faucets are different from those of domestic faucets. Generally, the water pipe of the imported faucet is soft and hard, and the hose (stainless steel braided pipe) is the most, and the end of the movable nut has an inch of 3 8 inches, and the matching can only choose the imported triangle valve, in addition, the nozzle of the sewer assembly is 11 4 inches.

1. Installation of single-hole basin faucet.

When buying a single-handle basin faucet, you should pay attention to the diameter of the water outlet, most of the water inlet on the market now belongs to the hard pipe, so you should pay attention to the height of the reserved water inlet, 35 minutes from the basin down is the most suitable. When installing, a special angle valve must be selected, and the angle valve must be fixed with the cold and hot water pipe of the wall outlet. When you notice a distance between the angle valve and the faucet water pipe, go and buy a special extension pipe to connect.

Remember, be sure not to use other water pipes to connect, because if the water pressure is high, it can easily fall off and leak, causing you losses. If the inlet pipe is too long and exceeds the outlet pipe, you can cut off the part according to your needs, and if the angle is not suitable, you can bend it moderately to the position you need as needed. Remember:

Do not bend hard to 90 degrees or greater than 90 degrees. When installing the basin to drain the water, do not forget to buy a small connector (short to the faucet). Don't forget to rinse the water pipes buried in the wall before you install them.

2. Installation of shower and bathtub faucets (wall-mounted).

Once you've purchased a shower, bathtub, or wall-mounted faucet, you can choose the right height for your plumbing. The spacing of hot and cold water pipes must reach 15 cm. Don't forget to rinse the water pipes before installation, so as not to damage the faucet due to the water quality.

Concealed shower and bathtub faucets: After purchasing concealed faucets, the valve core of the faucet should generally be embedded in the wall. Be sure to pay attention to the thickness of the bathroom wall before embedding.

If the wall is too thin, the spool will not be able to be buried. Do not easily remove the plastic protective cover of the valve core when it is buried, so as not to damage the valve core with cement and other chores during the embedding. In addition, when the valve core is embedded, you should also pay attention to the direction of the valve core up and down, left and right, so as to avoid the valve core being buried wrong.

If there is a deviation in the size of the wall-mounted faucet when the water inlet pipe is embedded, it can be adjusted with an adjustable crutch for calibration.

3. Installation of thermostatic faucet.

Before installing the thermostatic faucet, please check whether the water pipe is hot on the left and cold on the right, and remember not to connect the hot and cold water pipes incorrectly, so as not to prevent the faucet from working properly. Gas and solar water heaters cannot use thermostatic faucets because the water pressure is too low. When installing a thermostat, don't forget to install a hot and cold water filter.

4. Installation of single-hole kitchen faucet.

It is required to be stable, because the kitchen faucet is used more frequently, and it is easy to loosen when it is moved around, so the lock nut must be tightened. At present, there are some faucets on the market for the solenoid to increase the nut fixation, this kind of stability effect is very good, if you can solve the problem of water lifting, it will be a popular trend in the future.