What is the reason why the tank of the flush toilet is not watering

Updated on Toilet 2024-05-27
3 answers
  1. Anonymous users2024-01-24

    Reasons why the toilet does not pump water: 1. The water pressure in the home is too low. 2. Confetti is clogged. 3. The filter screen is clogged with scale. 4. The toilet parts fall off. 5. The inlet and outlet valves are faulty. 6. Improper tube design.

    Toilet does not pump solution:

    1. If the water pressure is not enough, the water flow is not enough to cause the water to stop, the total water door can be completely opened to increase the water volume, if the pressure and water level can not be increased, you need to find a municipal water supply company to solve.

    1. If the toilet does not pump due to blockages, then you must buy a soft body to dredge the pipe, and use it to hook up the blockage of the toilet, so that the toilet can be pumped. If the blockage doesn't hook up, then buy caustic soda and give it a try. Pour caustic soda into boiling water, wait for it to melt and pour it into the toilet, and after about ten minutes, the toilet can be opened, so that the toilet can be pumped.

    2. If it is the cause of the scale blockage of the filter screen, then the filter screen should be removed, and then the filter screen should be cleaned, and then the filter screen can be installed to pump water.

    3. If there is a problem with the inlet and outlet valves of the toilet, then turn off the inlet first, observe whether there is anything up to the inlet valve, and adjust the orientation of the inlet valve, and then open the inlet, and then the toilet will be pumped.

    4. If there is a problem with the toilet part, then it is necessary to observe which part it is. At this time, it is necessary to open the lid of the water tank to observe, if the float is damaged, then you need to buy a new float and install it again.

    5. If it is caused by improper design of the pipe type, it is necessary to re-decorate the pipe type, which will be more troublesome, and it is necessary to ask professional workers to carry out the construction, and the toilet can be pumped after the construction.

  2. Anonymous users2024-01-23

    1. The situation of less water from the faucet is a problem. Even the better toilet bowl has a filter inside, and the filter is blocked by too much limescale for a long time, so that the tap water cannot come in. As long as you can remove the filter and clean it, you can do it.

    2. Close the valve on the hose connecting the water inlet of the water tank, or the operation will spray water after a while. Flush the toilet again and drain the remaining water from the tank.

    3. Along the water inlet hose, look at the bottom of the toilet, there is a hexagonal nut to connect the hose with the water replenisher in the water tank (a standing plastic pipe) together, turn the nut with a wrench, and then look up along the position of the nut, there may be a nut in the same position, the same turntable, the same function, also unscrewed, my family is plastic, I don't know what else is the same as this. After two processes, the water replenisher can be removed from the inside of the toilet.

    4. Remove the water replenisher, see that there is a small square column in the middle of the inner tube, pull it out with needle-nose pliers, and you can see that the square column and the filter screen are one, and they come out together.

    5. Use a waste toothbrush or the like to clean the filter. It's better to have a scale cleaner, no and it's not a big problem, I just use the scale remover to soak the filter for a while, it is very clean, you can also pour some of this mixture into the water filler, you can also remove the scale inside. All cleaned.

    6. Finally, you can install it back as it is.

  3. Anonymous users2024-01-22

    1.Close the toilet inlet valve first, then drain the water in the tank, unscrew the hexagon nut at the bottom of the toilet bowl with a wrench, take out the bad water replenisher and replace it with a new one, and then remove the filter to clean the dirt;

    2.If you find that the flush button is inelastic, replace it in time;

    3.If the pipe in the water part of the water tank is entangled, it can be straightened by hand.

Related questions
What is the reason why the flush toilet does not go water?
8 answers2024-05-27

The reasons why the toilet does not go down are as follows: >>>More

What is the cause of a leaking toilet tank, the flush toilet tank keeps flowing
1 answers2024-05-27

This is because the plug did not reset the last time you flushed, and you only need to press it a few more times to hear the plug snap and it won't leak again.

What causes the toilet not to absorb water
2 answers2024-05-27

There is a blockage in the sewer pipe or toilet bowl and needs to be unblocked.

What causes the toilet not to go water?
14 answers2024-05-27

1. One reason is that the water pressure at that time was relatively low, because many toilets are now pumped, and if the water pressure is relatively low, it will lead to the problem of difficulty in getting water. Another is that many houses are on the upper floors, and when it comes to the peak of water use, the overall water pressure is relatively low, which also leads to the inability to get water. >>>More

What is the cause of flush toilet drainage
2 answers2024-05-27

Reasons for flush toilet drainage:1It was not installed well when it was newly installed; 2.It may be used for a period of time and the water seal is damaged. If it's the reason for 1, hit someone and reinstall it; If there is a reason for 2, the waterproof rubber band can be disassembled and replaced.