How to fix a leak in a flushing toilet after flushing?

Toilet leakage after flushing is caused by the toilet flush valve not being closed tightly, and can be repaired using the following methods.

Materials required: slotted taper, rubber sheet, double-sided tape.

1. Take the lid of the toilet tank away first, so that you can see the toilet flush valve group.

2. Pull the toilet suction valve group up to take out the valve group.

3. The blue cover of the valve group can be removed from the outward mouth.

4. After that, you can see the pumping valve of the toilet pumping component, and the middle of the bottom of the pumping valve is a sealing ring, if the sealing ring is not tight, it will lead to water leakage.

5. Remove the gasket under the sealing ring, stick the sheet to the bottom of the sealing gasket with double-sided tape, fix it and then install it back, so that the toilet will not leak.

After the flushing toilet leaks, you can first check whether there is a big crack at the bottom of the water tank, because the water in the water tank is not exhaustive, as long as the height of the water in the water tank is lower than a certain value, the water inlet valve will immediately supply water to the water tank.

If there is no big crack at the bottom of the water tank, it is caused by the aging of the sealing ring of the water tank drain valve or the loosening of the screw of the drain valve.

First of all, take the toilet tank cover away, so that you can see the toilet pump valve group, pull the toilet pump valve group up to take out the valve group, take out the valve group blue cover can be removed by deducting it outward, and then you can see the pump valve of the toilet pump component, the bottom of the pump valve is a sealing ring in the middle, if the sealing ring is not tight, it will lead to water leakage, remove the gasket under the sealing ring, stick the sheet to the bottom of the sealing gasket with double-sided tape, fix it and then install it back, so that the toilet will not leak.

If there is a problem, it needs to be removed and cleaned and replaced, if it is still leaking, it needs to be replaced with a new scoop. If the scoop is fine, see whether the rubber pad at the sink hose interface is aging, and replace it with a new rubber pad in time.

1. The surrounding area of the toilet seat is very clean, and the residual bacteria are very many, which is due to the fact that when flushing the toilet, it will cause the stains in the toilet bowl to splash on the toilet seat, if it is not cleaned up in time, when people use it again, the bacteria will stain the surface of the human skin, thus causing various diseases, so every time the toilet is used, the toilet seat must be cleaned.

2. After the toilet is used, it needs to be flushed to dispose of the internal excrement, and if there are yellow spots left in the toilet, you must brush it off with a brush, otherwise after a long time, the yellow spots will solidify, and it will become very troublesome to clean up. Also, be sure to close the lid of the toilet bowl when flushing.

3. Around the toilet, it is generally necessary to place a garbage can, so that the waste paper used daily can be thrown into the trash can, which can effectively place the toilet to be blocked. However, we must develop a good habit of cleaning out the bags in the trash can every day, otherwise it is easy to breed bacteria, which will affect the use.

What should I do if the toilet button doesn't respond? What should I do if the toilet won't flush? What should I do if the toilet flush is too small? What should I do if the toilet leaks and seeps? Life hacks.

Step 1: Remove the blue integral inlet valve on the left. (If it is a leaking water inlet valve) Step 2: Take off the hat of the inlet valve.

Step 4: Separate the two parts, and remove them to turn counterclockwise, with the help of small pliers. It is installed clockwise, and it can be installed by pressing it.

Step 6: The following part can be dismantled again, but it is here that the water is closed, and a few copies can be repaired by placing the small transparent lid on it.

Step 7: Turn on the shower switch and let in the water.

Step 8: Lift the float and the water stops to prove that it has been repaired.

1. The toilet tank has a spherical float that will be connected with the water inlet switch, first of all, we should check whether the connection is loose, and whether the float is in place and the switch is closed, if it is not closed, the water will not stop, and the water will flow out of the upright drain pipe after it is full.

2. The rubber ball valve is broken, so that the sealing is not tight, it will lead to water leakage, and this kind of emotional maintenance method only needs to buy a new rubber ball valve to replace it.

3. The rubber gasket of the drain port under the ball valve is aging and the sealing is not tight, and the maintenance method in this case is only to buy a new rubber gasket for the drain to replace. (Professional maintenance master is required).

4. If the interface between the toilet inlet and the sewer pipe is cracked and leaking, the toilet needs to be disassembled to expose the bottom, and then reinstalled after repairing the crack. (Professional maintenance master is required).

If the toilet leaks after flushing, you can first check whether there are big cracks at the bottom of the water tank, because the water in the water tank is not endless, as long as the height of the water in the water tank is lower than a certain value, the water inlet valve will immediately supply water to the water tank. If there is no big crack at the bottom of the water tank, it is caused by the aging of the sealing ring of the water tank drain valve or the loosening of the screw of the drain valve. First of all, take the toilet tank cover away, so that you can see the toilet pump valve group, pull the toilet pump valve group up to take out the valve group, take out the valve group blue cover can be removed by deducting it outward, and then you can see the pump valve of the toilet pump component, the bottom of the pump valve is a sealing ring in the middle, if the sealing ring is not tight, it will lead to water leakage, remove the gasket under the sealing ring, stick the sheet to the bottom of the sealing gasket with double-sided tape, fix it and then install it back, so that the toilet will not leak.

Replace the water parts, or adjust the water level control in the water tank, generally the water level control is too high, or the automatic water shut-off device is not easy to use.

If there is such a problem, it is generally that the leather ring is damaged, or the water level adjustment exceeds the control position, or the float does not play a controlling role, if it is not the above problem, then the whole set of accessories has to be replaced.

The problem of the components in the water tank The leather ring is loose, open the water tank, study the structure inside, and understand it by yourself.

Water leakage caused by aging of the parts inside the water tank, water leakage caused by unobstructed drainage pipes, water leakage caused by sewage backflow, leakage of toilet flush switch, aging of rubber gaskets at drain outlets, so water leakage.

If the rubber ball valve is damaged, the seal is not tight, and there is water leakage, replace it immediately. Water tank leakage, basically a problem with the drain valve, check if the flush switch is reset. The plastic flush switch of some flush toilets will occasionally get stuck after being worn for a long time and cannot be restored.

Generally, the switch can be reset by repeating it several times. Check whether the rubber gasket of the drain is aged and the seal is not tight, and if a problem is found, it needs to be replaced.

Don't be so professional and troublesome, simple water leakage and water seepage to hit the waterproof sealing glass glue on the line, acidic more sticky but will smell, neutral taste is small but the degree of pasting is average Depending on the situation, the web link was chosen.

If the flushing toilet leaks after flushing, it could be due to the following reasons:1The fittings inside the tank are damaged or aged and need to be replaced.

2.The water level regulator inside the tank is adjusted too high or too low and needs to be adjusted. 3.

The water valve inside the tank is not completely closed and needs to be checked and closed. 4.The water pipe connections inside the tank are loose or broken and need to be re-fixed or replaced.

5.The toilet bottom seal is aged or broken and needs to be replaced. Repair Method:

1.Replace damaged or aging fittings, such as water level regulators, water valves, etc. inside the tank. 2.

Adjust the height of the water level regulator so that the water level is in the correct position. 3.Check that the water valve is fully closed, and if not, it needs to be adjusted or replaced.

4.Check whether the water pipes are loose or damaged, and if so, need to be re-fixed or replaced. 5.

Replace the bottom seal of the toilet bowl to ensure a good seal. If the above methods cannot solve the problem, it is recommended to ask a professional plumbing worker to carry out maintenance and maintenance.

If the flushing toilet leaks after flushing, here are some things you can try to fix the problem:

Check the inside of the tank: Open the lid of the tank and check the inside of the tank for obvious broken or loose parts. Make sure all the parts inside the tank are installed correctly and tightened.

Check the water tank filling valve: Check if the water tank filling valve is closed properly. Sometimes the filling valve does not close completely, causing the tank to continue to fill and overflow. The position of the filling valve can be adjusted or the filling valve can be replaced to solve the problem.

Check the flush valve and gasket: The flush valve and gasket are responsible for controlling the flow of water and sealing the tank. Inspect flush valves and gaskets for damage, wear or clogging. If there is a problem, the flush valve or gasket can be replaced.

Adjust the flush chain: Check the position and tightness of the flush chain. If the chain is too long or too loose, it may cause the flush valve to not close properly or open completely. Adjust the length of the chain so that it is properly attached to the flush valve.

Check the bottom gasket: The bottom gasket is located around the drain at the bottom of the toilet, and it acts as a seal. Inspect the bottom gasket for wear or age, and replace it with a new one if needed.