How to unload the wooden sliding door of the balcony at home on the top of the door .

In the traditional decoration, the balcony is installed with sliding doors, look at the different designs of my balcony, which attracted a lot of neighbors!

In fact, the function of the balcony is not only to wash and dry clothes, which is a waste of space. Nowadays, the price of commercial housing is very high, and the space of the balcony should also be effectively used when designing. The reason why sliding doors are installed on the balcony is mainly to speed up the refrigeration function of the air conditioner when the air conditioner is turned on, so as to avoid mosquitoes and insects flying indoors.

Installing a sliding door on the balcony also has the effect of heat and moisture insulation and mildew resistance, and most people may only use the balcony as a place to dry clothes.

When my house was designed, the living room and balcony were directly connected, so the design was not only beautiful; It also improves the utilization of space.

The balcony has good lighting and view, the overall sense of space increases, and a relaxation area can also be designed on the balcony. Therefore, when decorating the house, it is not necessary to install sliding doors on the balcony. The disadvantage of installing sliding doors on balconies is that the space looks closed, which also affects the overall aesthetics; It is inconvenient to take care of it in daily life.

Nowadays, small houses should improve the utilization of space in the design, do not install sliding doors, and can design the balcony as a leisure area, tatami mats, study rooms, etc. The above is through the decoration of my home, summarized about the experience of decoration, to share with you, I hope you can learn and learn from the decoration in the future.

This is a crane wheel and hanging rail, and the disassembly is very simple.

At the top of the two sides of the door, that is, the side of the hanging wheel at the upper mouth of the door, there are two fixing screws, and the crane wheel can be separated from the door by loosening it with a cross lift, and the left and right two hanging wheels are removed, and the wooden door is down.

This is the hanging door, to remove the wooden door:

After removing the limit pin in the ground, the wooden door can be shaken.

At the top of the two sides of the door, that is, the hanging wheel side of the upper mouth of the door, there are two fixing screws on the 90-degree right-angled metal parts, and they are loosened with a cross lift (to hold the door, be careful to fall).

Carefully separate the door and the crane from the door, and the wooden door will come down.

Then remove the left and right two crane wheels and it is completedExtended Materials The sliding door from the living room to the balcony is best not to be removed, as it is very useful. It can be insulated in winter and in summer. Much more effective than installing curtains.

I don't know what the hanging pulley on the top of your sliding door looks like, you can see the bent iron piece of the pulley on both sides of the door, there is a Phillips screw on it, there are on both sides, remove this screw, and then pull the pulley outward. If it is two doors, there is a fixed fitting above the door crack after the door leaf is closed, which must be removed first.

Excuse me, how did you remove the hanging rail door, I was also stuck on the positioning pins.

You can lift the door up and see if you can get out of the track below. Then there is whether the track is spring-loaded or not. And then it's a matter of unloading the track, and it's better to show you a picture.

Cold, twist the screw on the screw between the hanging plate and the hanging wheel.

The sliding door does not move, the cause of the abnormal noise and the solution.

1) Reason: Mainly the lubrication and rust prevention of the slideway and small wheel.

2) Use lubricating materials: to use sliding door wheel rail grease, Senge and other well-known sliding door brands use tiger head hotolube or Kruber sliding door wheel rail grease. It is colorless and odorless, and has good durability.

There are security certifications. There are 130 grams of tubes in the hedge. , easy to use.

The maintenance interval is half a year.

3) Coating method: First of all, clean the slideway carefully, apply the grease into the slideway and pulley, pull the door several times, the grease will penetrate into the slide and the bearing, and then pull it very smoothly.

I also encountered the same problem, one side of the door is an exposed pulley, and the other end is hidden, mine is to rub the door frame edge sealing panel down (push), and then lift the door up and take out the pulley.

Stand on a high place and take a look, there are two iron plates between the top of the door and the small pulley, use a screwdriver to push the pulley to one side, a door has the same structure at both ends, the same way, push it out.