-
Anonymous users2024-01-24The commonly used glue for edge banding of panel furniture is yellow glue (neoprene rubber), before gluing, it is necessary to paste masking paper to protect the edge of the board to avoid leakage and pollution, and then glue the board, and then glue the edge banding, and then glue it, and then trim it after drying n hours.
1. Put the plate to be edge-banded on the workbench, prepare the edge banding strip, utility knife 2, repair the burr of the unsealed plate, otherwise the hot-melt adhesive is not firm, and the edge banding strip is easy to fall off 3. After repairing the burr, you can paste the edge banding, pay attention to pressing the edge banding strip when pasting 4, pressing the edge banding strip, so that the edge banding strip and the plate are closely fitted together 5, after compression, you should use a utility knife to remove the excess part, so that the plate is beautiful 6, the edge of the plate should be handled well, otherwise it will affect the user's senses when using it, In particular, care must be taken when processing the outermost part of the plate, so that it cannot be cut.
7. After the edge banding is completed, the cut and defective places should be repaired.
When repairing the plate, the heart must be careful, otherwise it is easy to leave scratches on the plate.
-
Anonymous users2024-01-231.Finishing method.
The sides of the parts are painted with paint and closed, i.e. they are first filled with putty, and then primer and topcoat are applied. The type and color of the paint should be selected according to the flat trim of the part.
2.Edge banding.
The edge banding method is to use veneer strips, impregnated paper laminated strips, plastic film to seal the side of the parts, or thin strips can be used to seal and paste. The edge banding process includes manual operation and mechanical sealing. The adhesive has developed from bone glue and leather glue to the commonly used synthetic resin glue, hot melt glue and polycopolymer resin glue.
Hot pressing edge banding has developed from manual ironing to the current resistance heating, low-voltage electricity.
Thermal, high-frequency heating and hot melt hot sealing. The edge banding process is as follows: gluing on the side of the component - attaching the edge banding material - adhesive curing - trimming.
3.Flangering.
The framing method is to wrap the side of the component with wood, plastic strips or metal materials, glued and grooved around the perimeter of the part.
4.Hemming method.
The edging method is to use a finishing material larger than the plane of the plate component, paste the plane and then bend it to the side to seal the side, this method is often used in particleboard, MDF components.
The whole decoration process can be divided into two stages: hard decoration and soft decoration, after the construction and main material installation is completed, it will enter the stage of soft decoration, at this time each owner can add their favorite items according to their personal preferences, so a series of soft decoration articles have been prepared. >>>More
Panel furniture is paint-free (paint-free). Moreover, the melamine paper on the surface after pressing and pasting is scratch-resistant, light-resistant, and generally acid-alkali resistant, etc., which will be stronger than paint. The edges of panel furniture are hot-pasted with PVC or paper edge banding
The edge banding of modern panel furniture is widely used in straight edge banding, special-shaped edge banding (soft-formed edge banding) and post-forming edge banding. The most common of these is straight edge banding. >>>More
It's better not to, just rest when you're pregnant, safety first.
Trimming is not whitening is the basic requirement of edge banding, many edge banding factories do not do well enough in the substrate color mixing, can only rely on the surface printing behind to adjust the color, although the surface of the edge banding tape looks consistent with the color of the plate, but as long as a trimming, it will leak out the color of the edge banding substrate. Therefore, there will be obvious color differences, resulting in obvious white leakage on the edge of the board, which will affect the quality of the product. >>>More