How to knit a toilet sleeve with wool

Preparation materials: about 2 halves of medium coarse wool, needle 10, weaving all stitches are weaving back and forth flat needles.

1. The main line ordinary method starts with 40 stitches (about 4 and a half inches) and weaves 10 rows.

2. After weaving 6 needles on the main line, change the thread to weave 28 needles, and throw 6 needles on the left needle without weaving.

3, in turn with the wiring to weave 26 needles, throw 2 needles (the original 6 needles of the main line is still not weaving), so that each line of the last 2 needles, 2 sides of each 8 needles, then the thread on the reverse side, has been woven to the right needle on the 8 knitted.

4. Turn over and change the main line, at this time, the main line is at the 6th needle, and the rest is all knitted.

5. A rainbow ends, so that a total of 21 rainbows are weaved.

6. After knitting 10 more rows of the main line, lock off 20 stitches, and continue to knit the remaining 20 stitches for 10 rows.

7. After weaving, the interface can be sewn.

Materials to prepare:

2 taels of brown medium coarse acrylic velvet, 1 tael of yellow medium coarse acrylic velvet, crochet needle, wool stick, scissors.

Specific weaving:

1. Prepare 47 needles from the brown velvet hanging needle method, weave a row of flat needles, and start to shrink a needle at the first end, and continue to weave flat needles, the effect is as follows.

2. After weaving 6 needles of the ninth row of brown thread, change the yellow thread to knit the flat needle to the remaining six needles at the other end, turn the head and still use the yellow thread to knit the flat needle to the beginning of the remaining one needle of yellow thread and so repeatedly knit 10 lines of yellow thread, the effect is as shown below.

3. Then the brown thread is retracted again at the beginning of the needle, and then the yellow thread is changed, and 10 rows are knitted in the same way as the weaving method when the yellow thread is used for the first time, and then the brown thread is changed to finish the yellow part, and the effect is as shown below.

4. Next, the 21st brown pattern part, add a needle every other row at the place where the needle was just added, a total of 8 rows and 4 needles are knitted, so far, the brown part has become 47 needles at the beginning, and the effect is as follows.

5. Secondly, after 34 rows of flat needles are woven alternately with brown and yellow two-color threads, 21 needles at each end, the 21st needle at the front and rear as the center, and 2 needles are contracted in each other row, so that a total of 12 needles are contracted in each place, a total of 24 needles, and then all the needles are flattened, and the effect is as follows.

6. Finally, the two ends that are naturally merged together are stitched, and the cushion is completed, and the effect is as shown below.

Toilet cover weaving:

1. 38 needles from the red up and 6 rows of needles back and forth;

2. Leave 10 needles on the left and right sides without weaving, and change the white thread to weave 18 needles and 6 rows in the middle;

3. 6 rows of 38 needles in red weaving, 6 rows of white in the middle, repeating 40 groups of red and white.

4. Weave 12 red needles on the left side, know 60 lines, and make the bottom. Remember to keep the buttonhole (hang it for a while, then two stitches and a while, and the second line is knitted normally).

5. Empty 5 needles, all not woven, as a gap in the toilet link position.

6. The rest continue to be red and white in 5 groups (the 10 stitches on the right are always red, and the weaving method is the same as 1-3), and the needle edge is sewn.

If it is for every 4 rows, it is necessary to weave 63 repetitions, and then weave 8 groups for upper stitching.