Why is the toilet not flushing strongly?

Reason 1: The side handle chain of the side press and side wrench toilet is long, which causes the water stop pad to stop the water quickly, although it moves.

Solution: Please shorten it to the appropriate level.

Reason 2: The top press lever of the top press toilet is low, which causes the water stop pad to stop the water quickly, although it moves.

Solution: Open the water tank cover, reverse, loosen the pressure rod nut, and adjust the length of the pressure bar to the appropriate one.

Reason 3: The water level of the inlet valve is low, resulting in weak water outlet.

Solution: Remove the inlet valve and remove the inlet valve buckle. Turn the inlet valve body counterclockwise.

Then increase the height of the body accordingly. Then rotate the inlet valve body clockwise and attach the buckle. Finally, install the inlet valve.

Connect the filter and water inlet pipe, and the fault can be eliminated.

Reason 4: The ceramic glaze of the toilet bowl is not smooth enough, which is easy to hang dirt, and it will also cause the flush to be unclean.

Solution: If there has been a similar situation, it is a product quality problem, the glaze material is not good, let the merchant come to deal with it. In the past, it could be rinsed, but now if it can't be cleaned, clean it frequently, and don't use too corrosive washing liquid, which will damage the ceramic glaze and make it easier to hang dirt in the future.

Reason 5: Ceramic hanging stains.

Solution: In general, it is good to brush directly with a toilet brush. If it is always easy to get dirty, a good toilet with ceramic glaze is better, use cheap toothpaste, be careful to be white, not the transparent kind, and then scrub with the green or blue rough side commonly used for dishwashing.

If you haven't cleaned it for too long, you can use a steel wool ball to gently wipe it first. However, the use of steel wool balls and decontamination powder will damage the ceramic glaze, so it is recommended not to use it.

Reason 1: The flange interface is installed when it is biased, and the sewer flow rate is reduced.

Solution: 1. When buying a toilet: It must be noted that the water pipes from the general tank to the tile are about 30 875px, and their diameters are 2750px.

2. When installing the toilet: supervise the whole process, and be sure to confirm that there are no mistakes in the installation location and method, otherwise if there is a problem, the whole will be dismantled and reinstalled.

3. After installing the toilet: do not test the water immediately, if you test the water immediately, it will flush away the cement at the bottom, causing the toilet to be unstable and leaking from the bottom. Do not use it right away, because the bottom cement is not dry.

Reason 2: The toilet itself does not have enough pumping power and insufficient water pressure.

Solution: 1. You can increase the amount of water, such as putting bottles in the water tank.

2. Adjust the screw of the water inlet valve clockwise to let the water level rise, and pay attention to the water at least 10mm away from the overflow nozzle of the drain valve.

3. Adjust the water level of the water tank appropriately. If it is a slow flow from the water tank to the toilet, check whether there is something blocked from the toilet tank to the flushing outlet.

Reason 3: Insufficient flushing water, water outages and other problems.

Solution: 1. If the amount of water is insufficient, you can take off the lid of the water tank and adjust the amount of water. There are two plastic rods under the toilet water button, and there are cocks on them to adjust the length of the plastic rods to control the amount of water.

2. If it still doesn't work, you can only change the toilet, you can choose the siphon toilet, the effect is good.

Reason 4: Long-term use has caused the sewer pipe to be contaminated with dirt, resulting in a smaller sewer.

Solution: You can remove the sewer pipe, put it into the acidic substance, eliminate the accumulated dirt, and then install it, and the sewer will be much faster. If there is a soft object blocked, you can use a soft spiral pass, or kick it with a toilet, if it is a hard object, it is best to find a professional company to solve it.