-
Anonymous users2024-01-231. Bathroom decoration toilet installation process - punching.
After determining the installation position of the toilet, align the bottom sewage outlet of the toilet with the ground sewage nozzle, and then draw the position of the fixed hole at the bottom corner of the toilet on the ground according to the peripheral size of the toilet base, and punch the hole with a percussion drill, the general hole depth is about 5cm.
2. Bathroom decoration toilet installation process - toilet positioning.
After the eyelet is laid, hammer the steel expansion bolt into the eyelet, put it into the bottom corner of the toilet, and tighten the nut to position the toilet. Note: The toilet drain should be tightly connected to the toilet floor drain pipe and need to be sealed.
3. Bathroom decoration toilet installation process - fixed toilet.
According to the height of the purchased toilet tank and the position of the eyelet on the back wall of the water tank, find the fixed position of the toilet on the wall to punch the hole, and then knock the steel expansion bolt into the hole, the water tank is in place, make the back wall eyelet into the expansion bolt, add a 3mm thick nylon washer and put the nut on it and tighten it. (In the case of a one-piece flush toilet, this step can be omitted.) )
4. Bathroom decoration toilet installation process - connecting pipe installation.
After the water tank is installed, you can start to install the connecting pipe between the water tank and the base of the flush toilet, and the connecting pipe between the water inlet pipe and the bottom of the water tank for water supply. Remember, you need to install an angle valve at the connection of the inlet pipe, that is, a control valve!
5. Bathroom decoration toilet installation process - accessories installation.
Install the floats, water scoops and other accessories in the water tank.
6. Bathroom decoration toilet installation process - detect the size of the water spray.
After the fittings in the tank are installed, they need to be tested. Open the water inlet valve, observe the height of the water required in the water tank, adjust the height of the float water scoop, and adjust the tightness of its control screws according to the size of the water spray valve.
7. Bathroom decoration toilet installation process - detect the sewage effect.
After completing the inspection of the fittings in the water tank, you can check the sewage effect of the toilet bowl and whether there is any leakage in the connection between the pipes.
8. Bathroom decoration toilet installation process - sealing work.
Once the test is complete and everything is correct, the gap between the toilet base and the floor can be sealed with a material such as putty or silicone. (Note: Cement slurry, cement mortar, etc. cannot be used as sealing materials here!) )
9. Bathroom decoration toilet installation process - install the seat ring and toilet cover.
Install the seat and toilet lid of the flush toilet. At this point, the flush toilet is installed.
-
Anonymous users2024-01-22The bolts of the toilet lid in the open place can be removed directly, and then the adjusted toilet lid can be installed on the toilet, because the size is not divided into sizes, so after the bolts are adjusted, it is OK to fix the screw cap against the two holes. When replacing the toilet seat, you only need to remove the fixed spiral at the back of the toilet bowl, and operate in the opposite direction when installing the new toilet seat.
Start by removing dust with tweezers.
granules, then repeated with water. >>>More
Flip up and down to see if there is any gap in the connection of the cover, mainly the seat ring, the rear of the bidet, and the main board. These places have strict requirements for moisture-proof and leakage-proof.
Let's say that it must be unqualified, maybe the manufacturer says that the problem is high quality for half a year, so this is the reason why many products are repaired for three to six months. If the manufacturer doesn't solve it, it's impatient!
1. Before the installation of the toilet, check whether there is any blockage of sediment and debris in the sewage pipe, and whether the installation ground is level. The toilet sewage pipe should be made of plastic pipes required by the national standards, and the inner wall of the pipe should be smooth, flat, no bubbles, no cracks, no obvious marks and depressions. In particular, it is necessary to ensure that the sewage pipe is about 10mm above the ground. >>>More
Try not to tear off the logo on the smart toilet seat, because he told us how to use it.