As soon as the toilet is flushed, the base leaks

<> toilet leaks as soon as the flush base is flushed: 1. The toilet installation problem occurs when the toilet is flushed, and the toilet leaks when it is flushed, which is that the toilet is not sealed at the beginning of the installation of the toilet, and some netizens buy the toilet from the Internet and install it themselves, and the flange and the toilet drain are not aligned well when installing the toilet, and it will naturally leak out of the toilet base when flushing.

There is also the inconsistency between the diameter of the toilet drain and the diameter of the sewer, in this case, we must pay attention to the fact that it is necessary to measure it in advance before buying the toilet, if it is not measured well, it will lead to a gap between the toilet drain and the sewer mouth, which must be leaking.

2. The sealing problem of the toilet mainly includes two aspects, one is the toilet flange sealing problem, and the other is the problem of adding glass glue to the toilet base. If the glass glue between the toilet base and the tile is broken, there is also a possibility that the toilet will leak.

If it is installed in a specialty store, it is usually padded with a sealing ring inside, and the toilet bowl is placed with glass glue around it. Tools to prepare: utility knife, (if you need to disassemble the angle valve) water adhesive tape, wrench, glass glue and glass glue gun.

Toilet seals (need to be replaced if removed).

If it is a decoration of plumber and electrical tooling, it is usually made of white cement. Prepared tools: slotted screwdriver (used to eliminate the original white cement), white judgment such as cement (when reloading, first mix the water at the bottom of the toilet, and then put the toilet seat up and put it steadily, and then use the mixed white cement to seal the toilet footsteps in a circle, and then use it when it is dry.

Be careful not to let the white cement fall into the pipe, otherwise it will cause the pipe to be blocked.

> Reason why the bottom of the toilet seeps as soon as it is flushed:

1. It is likely that the toilet is not installed correctly, so there is no flange at the bottom, and there is no way to fix and defend it, so it is easy to seep water when flushing.

2. The long-term use of the excavation is suitable for the loosening of the toilet and the ground. The toilet toilet itself is a problem with cracks in the ceramic (rare). The toilet was not installed properly when it was installed, resulting in the misalignment of the sewage outlet on the ground with the toilet drain diameter.

In this way, yellow water, water and foul smell will come out. The repair method of leaking water in the two small holes of the toilet base confirms that the water parts inside the tank are installed correctly and tightly. It can be closed with glass glue at the bottom of the water inlet and the junction of the water tank.

3. The bottom of the flush part is also treated. Make sure that the rubber ring at the connection between the water tank and the toilet body is flexible enough, and that the connection between the water tank and the toilet body is tight enough. Apply the rubber ring between the water tank and the toilet with neutral glass glue.

4. Before the construction of the glass glue, please wipe the sizing part dry. Keep 24 years without water after construction.

5. Now due to the silica gel, many toilet installations are omitted to be fixed with expansion bolts, and directly fixed and sealed with strong adhesive silicone, sealed with putty for a long time, which will harden and cause cracking and leakage, and if the silica gel is not fully cleaned before bonding, it is also easy to produce local water leakage.

The toilet drain and the reserved drain do not fit well – you need to lift the toilet and reinstall it!

1. Toilet installation problems.

Toilet installation problems appear when the toilet is flushed, the toilet leaks, this situation is that the toilet is not sealed at the beginning of the installation of the toilet, some netizens buy the toilet from the Internet and install it themselves, the flange and the toilet drain are not aligned well when installing the toilet, and it will naturally leak out of the toilet base when flushing.

There is also the inconsistency between the diameter of the toilet drain and the diameter of the sewer, in this case, we must pay attention to the fact that it is necessary to measure it in advance before buying the toilet, if it is not measured well, it will lead to a gap between the toilet drain and the sewer mouth, which must be leaking.

Solution: If the toilet is not installed well, find a professional to install it from the new, the toilet flange can no longer be used after being installed once, and buy a new toilet flange, if the diameter of the toilet drain and the diameter of the sewer are inconsistent, this can only replace the toilet, or the drain can be filled with a flange, so as to avoid leakage when the toilet is flushed.

2. Toilet sealing problems.

The sealing problem of the toilet mainly includes two aspects, one is the sealing problem of the toilet flange, and the other is the problem of adding glass glue to the toilet base. If the glass glue between the toilet base and the tile is broken, there is also a possibility that the toilet will leak.

Solution: If it is a problem with the toilet flange, directly replace the new toilet flange, if it is a problem with glass glue, re-label the toilet base with new glass glue.

The reasons for a leak at the bottom of the toilet are:

1. There is a crack at the bottom of the toilet bowl caused by the toilet leakage, which is mainly caused by the poor quality of the toilet, and even the crack occurs when the toilet is fired, and the water leaks out along the crack when it is used.

2. The toilet and the ground are generally bonded with glass glue, if the glass glue is too little or the glue is too thin, in the cumulative use, it is easy to appear between the glass glue and the toilet or the ground, in this case, you can see whether there is an obvious gap between the glass glue and the ground, if so, you can shovel the existing glass glue clean, and then buy the relevant glass glue for re-bonding, under normal circumstances, try not to use the toilet in 24-48 hours after smearing.

3. The quality of the water parts in the toilet is not up to par, the toilet parts are aging after being used for a long time, the buoyancy of the float in the toilet tank is not enough, the float is mainly to control the water valve in the water tank, if there is a problem, the water valve can not be automatically closed, and the water will always enter the water, and it is easier to seep out of the base of the toilet when the amount of water is relatively large.

4. It may be that the sealing ring at the bottom of the toilet is not tightly sealed during installation, and the sewage outlet at the bottom of the toilet bowl and the diameter of the toilet are not aligned when the toilet is installed, resulting in the liquid overflowing from the connected place when the toilet is draining or discharging.

It should be the toilet seal that is degummed. Turn off the toilet bowl with water, then remove the toilet, reinstall it, seal it with glass glue, and everything will be fine after 24 hours. We hope you will adopt it.

The toilet is not installed well, the lower mouth is not aligned, use a knife to lift the toilet, use glass glue and white cement, the rubber pad in the toilet is broken, and it is okay to install the right water pipe first.

Don't spend money to replace the leaking water at the toilet base, use it to make it up easily, and it can be managed for a long time.

It should be sealed with glass glue, and the whole sits on it without leaving gaps; The installer did not seal the installation well, indicating that the cement or glue connecting the base and the ground was opened, and it needed to be dismantled and glued together again.

The rubber ring at the interface of the fecal pipe below and the toilet bowl is not properly connected, and it needs to be removed again to connect it.

Two reasons:

It means that the cement or glue connected to the base and the ground is boiled, and it needs to be dismantled and re-glued, and resealed with glass glue.

If the flange is not installed, or the position of the flange is incorrect, it will cause outward flow of water and debug the flange.

There are 2 problems: 1 is that the toilet downspout is not aligned with the drain pipe; 2. The glass glue between the toilet and the floor tile has been disconnected!

You can just wipe it with cement.

rom Iceland, Eston

It could be due to the following reasons:

1.The water level inside the tank is too high, causing water to overflow from the tank and into the base.

Solution: Adjust the water level in the tank so that it does not exceed the height of the overflow pipe.

2.The base's gasket is aging or broken, causing water to leak out of the base.

Solution: Replace the sealed early grandson pad.

3.The screws of the base are loose or damaged, causing water to leak out of the base.

Solution: Tighten or replace the screws.

4.The drain hole of the base is blocked, causing the water to not drain properly.

Solution: Clean the drain holes.

If the above methods cannot solve the problem, it is recommended to contact a professional toilet repairer for maintenance.

Causes and solutions for leakage of the toilet base as soon as it is flushed:

1. The sealing ring of the toilet base is not installed, or the connector is not connected, in this case, the toilet needs to be reinstalled, so as to effectively ensure that the base of the toilet does not leak.

2. There are certain problems with the quality of the toilet itself, so it is easy to crack after using it for a period of time, and the base of the toilet is easy to leak in this case. You can check the size of the crack, if it is relatively small, you can use glass glue to repair it; If it is larger, it is better to replace it with a new toilet.

3. If the float of the toilet is not buoyant enough, in this case, it is necessary to replace a new float, and it is necessary to purchase a float with the appropriate pressure.

>4. If the sealing valve cover of the drain valve is loose, then the toilet is prone to leakage when flushing. In this case, a better quality cap can be replaced.

5. There are certain defects in the design of the toilet tank, and it is also prone to water leakage, so you can choose to replace it with a new one, or find after-sales service personnel for maintenance.

6. The inlet valve of the toilet is not equipped with a filter, so there are more impurities in the water, which is likely to cause blockage, and also cause the base of the toilet to leak. In this case, it is necessary to clean the seal of the toilet bowl before installing a filter on it.

There is a crack in the seal between the bottom of the toilet bowl and the floor.

The installation of the toilet will be sealed with cement at the junction of the ground and the bottom of the toilet, and its function is also to prevent water from leaking out, in the process of toilet flushing, due to the pressure of the water, the water flow can not be guaranteed to flow in accordance with the "prescribed route", and some will even splash out, if the cement seal cracks will have clean water flowing out.