How to solve the phenomenon of siphon toilet flushing without siphoning

It should be that there is limescale in the water pipeline, and it is recommended to clean it with a professional descaler, which should solve the problem.

Siphon principle. It's the connector.

The principle. The siphon is filled with water, there is no gas, the water level at the incoming end is high, and the water outlet is closed with the palm of the hand or other objects. At this time, the pressure in the tube is equal everywhere. After everything is settled, open the water outlet, although the atmospheric pressure on both sides.

equal, but the water level at the incoming end is high and the pressure is strong, pushing the incoming water to flow out of the outlet.

> principle at a glance: Because the pressure difference is at work. When the pressure of the same liquid level on both sides of the elbow is different, the water (or other liquid) in the pipe will flow to the side with less pressure.

> use the siphon principle, three conditions must be met: the tube must be filled with water (or liquid) first. The height of the highest point of the tube from the water surface of the upper container must not be higher than the height of the water column supported by atmospheric pressure.

The water surface of the outlet must be lower than that of the upper container. In this way, the downward pressure (atmospheric pressure of adding water) to the outlet sheet is greater than the upward atmospheric pressure. Ensure the outflow of water.

> is at work due to the pressure difference. When the pressure of the same liquid level on both sides of the elbow is different, the water (or other liquid) in the pipe will flow to the side with less pressure. It is necessary to be able to produce a siphon phenomenon.

The water outflow end of the elbow must be lower than the water inlet end. <>

The principle of the flush toilet is mainly the siphon principle, and the structure diagram of the flush toilet is also based on the siphon principle. The "pumping" of the flush toilet refers to the S-shaped bend under the toilet, and when the water surface in the toilet exceeds the high point of the S-bend, the siphon phenomenon is formed, which can pump the water and dirt of the toilet together. Until only a small amount of water remains, the siphon destroys, leaving a small amount of water, forming a water seal.

Siphon: The phenomenon of siphoning is caused by the gravitational force and potential difference between liquid molecules. That is, the pressure difference of the water column is used to make the water rise and then flow to a low place.

Since the nozzle water surface is subjected to different atmospheric pressures, the water will flow from the high-pressure side to the low-pressure side until the atmospheric pressure on both sides is equal, and the water surface in the container becomes the same height, and the water will stop flowing. The siphon phenomenon is used to quickly pump out the water in the container. )

The siphonless phenomenon is caused by a clogged toilet bowl and can be solved with the following methods:

1. Find a half-inch wide bamboo strip and put it into the toilet to dredge it can solve the problem, and you must be cautious in the process of solving the problem.

2. Many times the toilet flushes more often, and it will pass by itself, especially if it is a soluble or breakable item such as soil and paper. If it's greasy, then rinse a basin of boiling water to melt it.

3. Buy some caustic soda, boil water to melt the caustic soda, and pour it into the toilet. After ten minutes, everything will be cleared.

4. Buy a puff and dig it yourself.

5. You can buy a loach and put it in the squatting toilet, pour it into the toilet with warm water, and the loach will desperately drill down when it is hot, so as to achieve the purpose of making a toilet. If there's nothing hard about it, I think it'll work.

6. The old-fashioned mop, fill the toilet with half of the water, and then press the hole a few times with the mop, the action should be fast, and rely on pressure to get it through.

7. Insert a relatively long flexible ventilation tube into it, ventilate it inside, and then flush the water.

8. Buy a simple toilet toilet, pour water into the squatting toilet, and then use the toilet suction basin to pump a few times at the mouth of the squatting toilet, which is passed by using its air pressure.

9. Fill it with water and throw a few soap heads into it to soak it to increase the lubrication function.

10. Find a professional who dredges the pipes.

It's not siphonless. It's called no suction, the toilet didn't test the water when it left the factory, if it's new, you can go to them, there is no way to do it without suction,

I would like to introduce a simple and practical method to you: first put the cloth strip mop we commonly use into the toilet, then fill the toilet with water, and immediately hold the mop rod after filling it with water, and repeatedly lift and press the mop up and down until the water is finished. After the toilet is drained, try to run the water smoothly, if it is still not smooth, just follow the above steps a few more times.

It seems that there should be limescale in the water pipeline, and it is recommended to clean it with a professional descaler, which should solve the problem.

How to solve the problem of slow draining of the siphon toilet without suction, have you learned.