The flush toilet suddenly stopped flooding

There are several reasons why the toilet does not get water:

1.Determine the water supply and angle valves and hoses first.

2.The small filter inside the lower end of the inlet valve body is blocked.

3.The inlet valve has been adjusted by itself, resulting in improper adjustment.

4.The quality of the inlet valve itself.

You can open the toilet lid to check whether the float sinks to the bottom when the tank is empty, if it is still above when there is no water, it means that the float is broken, and it cannot sink and the upper water outlet is always closed, so there is no water.

You can also check whether the triangle valve is open, remove the triangle, check whether the end connected with the inner wire in the wall is blocked by the raw material belt, whether the valve core of the empty triangle valve is open and closed normally, whether the water hose is smooth, and the same kind of exclusion can be done.

If there is no water and the figure-eight valve is broken, just go outside and find someone to help fix it.

Open the toilet lid to check whether the float sinks to the bottom when the water tank is not water, if it is still above when there is no water, it means that the float is broken, and it cannot sink so that the water outlet is always closed, so there is no water, you can also overhaul other reasons, whether the triangle valve is open, remove the triangle, check whether the end connected with the inner wire in the wall is blocked by the raw material belt, whether the valve core of the empty triangle valve is open and closed normally, whether the water hose is unobstructed, just a little thing, you can exclude it the same, If it is normal, then it is necessary to consider the problem of the water pipe, whether it is welded during construction.

The flush toilet was designed by an English priest named John Harrington. The toilet uses the water discharge knob and the water plug to control the water discharge and water storage, when using, rotate the water discharge knob, use the metal rope or nylon rope connected to the water plug to pull up the water plug, the water plug pulls out the water outlet pipe port upward, and the water outlet pipe puts the water into the urinal and uses the gravity of the water and the kinetic energy converted by the potential energy to flush the excrement dirt into the sewer pipe.

The flush toilet consists of the following main parts: inlet pipe, outlet pipe, seepage pipe, water plug (inlet and outlet), float, drain knob and lever, water refill mechanism, water tank, urinal (the urinal has a bend that connects to the water tank).

That pressure valve is broken, just fix it a little, it's not difficult.

Look at the hose connecting the wall under the water tank to see if there is water (there is a switch at the other end of the water pipe, called the figure-eight valve), if there is no water, the figure-eight valve is broken. If not, you remove the left part of the water tank picture, which is the water inlet part, take it to the building materials market to buy one, or try to fix it.

You lift up the blue thing with a small stick on the left side of the picture to see if it is watery, and if it is on the water, you move it up and down to see if it can be used. If you don't, it's even a plug in the hose under the toilet.

It is estimated that the inlet valve is blocked, and it should be usable to remove it for cleaning by yourself, and there is no problem with putting the transparent pipe like that.

Replacing a water ingress resistor will do.

1. The lever or float of the water supply component is stuck.

The lever in the toilet bowl water component is the transmission device, however, in the process of long-term use of the toilet, some scale or dirt may be attached to the activity point of the lever, making it not so sensitive, or even stuck, which also includes the float is also easy to stuck, that is, the float has been floating, in this case, the toilet inlet is sealed, and it cannot be automatically watered.

2. The outlet of the water supply component is blocked.

The water outlet of the toilet water supply component, you may not have seen it, it is a very small opening, mainly for easy blocking. Although the water flow rate will be relatively large due to the small spout, it will still be blocked by some scale or dirt if it is used for a long time. The water outlet is blocked, and even if the inlet valve is opened, the water will not come out, and the toilet will naturally not be flooded.