The kitchen sink pipe is not blocked, but what is the reason for the poor drainage?

1. Check whether there is a problem with the design of the sink itself, which makes it easy to collect water.

2 It's best to have a professional come to your door.

The kitchen sink pipe is not blocked, but what is the reason for the poor drainage?

The kitchen sink pipe is not blocked, but what is the reason for the poor drainage: the kitchen sink pipe is not blocked, but the reason for the poor drain is the pipe installation problem 1, the kitchen drainage, often contains a large amount of oil, grease condensation, so that the inner diameter of the sewer pipe becomes smaller, resulting in blockage, poor drainage. 2. Pipeline installation problems:

There may be two traps, one has been installed in the sewer pipe, and another one is brought when the sanitary ware is installed, which is easy to cause poor drainage due to the secondary water seal. If so, remove one.

The kitchen sink pipe is not blocked, but what is the reason for the poor drainage?

Generally, if the sewer pipe cannot be blocked, the sink drain has been checked; It should be that the downspout of the sink is raised too high to inhibit the flow of water. 1. The sewer in the kitchen often contains a large amount of oil, and the grease condenses, making the inner diameter of the sewer pipe smaller, resulting in blockage and poor drainage. 2. Pipeline installation problems:

There may be two traps, one has been installed in the sewer pipe, and another one is brought when the sanitary ware is installed, which is easy to cause poor drainage due to the secondary water seal. If so, remove one. 1. Leakage of the sink drain If the leakage of the sink is due to the leakage of the sink drain, generally speaking, the pivot washer in the sink should be destroyed, and only one of the pivot pads needs to be replaced.

Use needle-nose pliers to tie the gland and rotate it, take it out after it is loosened, and use an iron clamp to remove the crushed pivot washer and replace it with a new one. 2. Leakage in the gap at the bottom of the sink bolt The leakage at the bottom of the tank bolt may be caused by damage to the triangle seal in the gland. At this time, you only need to use a special tool to turn the screws of the faucet, take out the screws and tether after loosening, loosen the gland and take it out, and then remove the triangular gasket in the gland and replace it with a new triangular gasket.

3. Leakage at the joint of the sink Leakage at the joint of the sink Butt The reason for the leakage at the joint of the sink butt may be that the cover screw cap of the faucet is loose, and it can be solved immediately by tightening the cover screw cap again or replacing it with a new gasket. 4. The water pipe is brittle and leaking, the sealing is not timely, the water pipe is brittle, the sealing is not timely, and the hardware needs to be replaced. When installing hardware, all kinds of residues in the pipeline must be completely eliminated to prevent the valve core from being stuck and blocked.

There are some more inconvenient hardware replacements, and it is better to find technical professional maintenance personnel to carry out maintenance. 5. The sewer is blocked and the sewer is blocked, and the leakage is blocked, and the dirt must be eliminated, but it is better to dredge it by itself or let the technical professional staff dredge it to prevent the situation from getting worse and worse.

1. The sewer in the kitchen often contains a large amount of oil, and the grease condenses, making the inner diameter of the sewer pipe smaller, resulting in blockage and poor drainage.

2. Pipeline installation problems: there may be two traps, one has been installed in the sewer pipe, and another one is brought when the sanitary ware is installed, which is easy to cause poor drainage due to the secondary water seal. If so, remove one.

There is a pipe dredging agent called Ou Li Tong is very effective, go in at a point, and wait for a few minutes for the water to flush through. It can also remove odors, insects and eggs.

Generally, if the sewer pipe cannot be blocked, the sink drain has been checked; It should be that the downspout of the sink is raised too high to inhibit the flow of water.

There was too much grease in the main sewer and the lines needed to be cleaned.

It could be that the main sewer pipe is blocked, or that the sewer pipe in your home is too long and the drainage is busy.

First of all, ask what floor your family lives on, if it is a low floor, it is likely that the water pressure is not enough, in that case, you need to check the main pipe, I hope it will help you.

Please check the property for other sewer pipes.

The kitchen sink pipe is not blocked, but what is the reason for the poor drainage?

1. The sewer in the kitchen often contains a large amount of oil, and the grease condenses, making the inner diameter of the sewer pipe smaller, resulting in blockage and poor drainage. 2. Pipeline installation problems: there may be two traps, one has been installed in the sewer pipe, and another one is brought when the sanitary ware is installed, which is easy to cause poor drainage due to the secondary water seal.

If so, remove one.