How to deal with the whitening phenomenon after waxing the solid wood floor

After waxing, whitening is that the wax is mixed with water, which is not only whitening, but also has low adhesion, which is a failure type of construction.

Anti-static floor cleaner is best cleaned with powder cleaner, because the particles in the powder cleaner can wash out the stains in the pores of the floor and lay the foundation for the next step of anti-static floor waxing. At present, the powder cleaning agent brand Beijing Zhenjieshi product series "high-efficiency porcelain cleaning" is of good quality and is more popular in the industry.

After the cleaning work is completed, it is the anti-static floor waxing process, before waxing, you need to figure out the properties of the floor, to see whether it is a conductive or dissipative floor, because the resistance value required by the two is different, among which the resistance value of the test floor after the electrostatic dissipative floor is waxed must meet 1 106 and 1 109, deviation from this resistance value is regarded as an unqualified product, and the cleaning and waxing is regarded as invalid. If it is a conductive floor, then the maximum value of surface resistance measurement should be less than 1 106, and the minimum floor resistance test value should be greater than, at present, the performance of anti-static wax water on the market should be more stable (Anta) 3M anti-static floor wax, but now 3M products are too many fakes in the market to distinguish between them, it is recommended to take a few test points to do the average value test of resistance before waxing and carefully make a record, and then apply wax in a large area after the value reaches the standard, so as to avoid unnecessary losses caused by unqualified resistance data after cleaning and waxing. Here's a word, the price of anti-static floor wax is very high, and it is difficult to distinguish the authenticity of Li Kui and Li Ghost in the industry.

This phenomenon is caused by the dampness of the floor.

Solution: In this case, you need to remove the wax, and then wax after using a wax remover.

Note: After waxing the floor for a period of time, it is necessary to remove the wax regularly.

Floor waxing should be paid attention to:

1) Choose a fine weather for waxing.

If the humidity is too high on rainy days, waxing will produce white turbidity. When the room temperature is below 5 degrees, the floor wax will harden. Do not use a cloth containing chemicals to wipe the floor before waxing, as it will cause poor adhesion of the floor wax.

2) Remove garbage and dirt from the floor surface.

Use a vacuum cleaner to remove trash and dust from the surface of the floor. Wipe the stains on the floor with a diluted mild detergent, and use water to remove the hard-to-remove stains. To prevent detergent from accumulating in the trenches, wring out the cloth soaked in detergent as much as possible.

Floor wax removers can cause stains and swelling on the floor and should never be used.

3) Wipe with a wringed out rag.

Use a forcefully wrung cloth to wipe the surface of the floor, especially the grooved part, carefully and without leaving detergent residue. Residual detergent and moisture can cause the surface to be white and swollen.

4) Dry thoroughly.

The moisture on the surface of the floor and the trenches is completely dry before waxing. The time required varies depending on the season, but it usually takes more than half a day. If it is not fully dried, the floor wax will not adhere tightly to the surface of the floor, affecting the appearance and producing whitening.

5) Waxing method.

Shake the container with floor wax and stir well. Before waxing the floor of the room as a whole, a partial trial should be carried out in an inconspicuous place such as a corner of the room to confirm whether there is any abnormality. In order to prevent the floor wax from polluting the wall baseboard and furniture, the above parts should be covered with tape and paper, and the floor wax should be fully soaked with a clean rag to prevent it from dripping, and the floor wax should not be poured directly on the floor, otherwise there will be stains and circles.

Carefully apply according to the direction of the wood grain of the floor, do not miss the coating or uneven thickness, too little amount will cause uneven thickness, too much will lead to poor film-making, keeping the thickness uniform is the key to waxing, do not dilute the floor wax with water.

6) Do not walk on the floor before the floor wax is dry.

It usually takes 20 minutes to 1 hour to dry, and reapply if there is a leak. If waxing is done twice, the second application should be done after the first application is completely dry. Waxing every 6 months or so can keep the floor beautiful for a long time.

If the wax used does not react with the paint, it will slowly return to its original shape as it is used over time. Do not use paraffin wax, or low-cost ones, beware of reacting with floor paint, please use flooring special (flooring stores should be available).

Must use white lightning cleaner. This is a special cleaner for wood floor cleaning. It is a natural and environmentally friendly wax remover. The net is wiped clean and clean.

Judging from your question, it is estimated that you are using liquid wax.

Like you said, you need to do dewaxing to solve it.