-
Method 1: Find the screw cap, remove it by hand, and replace it with a new one.
Generally, the position of the screw cap is not easy to find, some are in the light, and some are in the dark. In the dark place of the screw cap, inside the toilet bowl against the side of the tank, open the lid. If you put your hand in it and touch it upwards and in the direction of the tank, you should be able to touch it, but you can't see it.
Method 2: When replacing the toilet seat, you only need to remove the fixing bolt on the back of the toilet to replace it, and you can operate in the opposite direction during installation. Most toilet seats are large or small, and you can simply adjust the two bolts when installing.
However, it is also necessary to measure the size, the distance between the screw holes, the width and length of the toilet seat, and then buy a new toilet seat to replace it.
-
Because it's too tight to squeak, you can loosen it up a little bit and it will make a sound again.
-
The lid of the toilet can be installed by itself, just like sometimes, the cushion on which the toilet lid sits is broken, and then, well, you can remove it and install it yourself, so you may be too tight, squeaky and rattling, you can remove it and reinstall the screws or loosen it, it doesn't matter, because sitting on it, it doesn't affect the tightness at all, so you try to reinstall it yourself, or your home, if it's a man, the man, turn it, and the normal woman won't do these things.
-
The toilet lid is too tight and squeaks when angry. It may be that part of the joint is there. Just loosen that area a little bit.
-
Drop a few drops of lubricating oil on the rotating part and the sound will disappear.
-
It could be the connection between the toilet bowl and the lid, where there is a problem, you can try to loosen it a little bit and it will not develop that sound again.
-
Pour some oil over the toilet seat shaft, turn the toilet seat until the sound is gone, and wipe the oil off the surface.
-
You can reach to the back and loosen that fixing screw.
-
Put some lubricating oil or something in the connection, essential oils are also fine, don't use cooking oil
-
Loosen the screws of the toilet seat or add some lubrication.
-
Adjust the tightness of the bolts of the connection and the angle of the toilet seat, and try it.
-
Loosen the screws, or you apply soap to the screws, and you're good to go.
-
The toilet bowl is too tight, and it makes a creaking sound when it is turned. Just use it for a while.
-
The screws that hold the toilet seat in place are tight, and you can loosen it with a change cone, and there will be no more sound.
-
Then remove the toilet lid and press it again so that it is not too tight and loud.
-
There are screws on the toilet seat, and you can loosen the screws on both sides.
-
Fill the shaft at the toilet seat junction with some oil.
-
You can rub a little oil.
Or touch it with sandpaper.
-
You can dot the shaft of the toilet bowl with something like soybean oil or pencil foam.
-
There's a place for him to loosen the toilet seat, right? If you let him go, he won't just think about it.
In the bathroom, we need to use toilets every day, toilet lid is one of its important components, if we usually use it, too much force or frequent opening and closing, it is easy to cause damage to the toilet seat. Once the toilet seat is damaged, it is more troublesome to replace and repair. So what to do if the toilet seat is broken? >>>More
The old toilet seat is installed with a threaded bolt, which must be equipped with such bolts to install, and the new one cannot be installed if the bolts do not match. I hope my answer can help you.
The power supply of a notebook is generally 65W, which means that the maximum power of a notebook generally does not exceed 65W. Calculated at 65W, 65W*24H=1560WH, that is, 1560Wh = kWh (kWh), the maximum power consumption per day.
I know of a toilet seat that is particularly easy to remove by pressing a button on the hinge. >>>More
There are bolts on the remaining two sides of the hand, unscrew it and put the new screw on top of it, and tighten the bolt.