How to fix the toilet seat damping is broken

The slow drop cover is a kind of oil that is generally used for 2 to 3 years, and when he misses or volatilizes it, the cover plate will not slow down. It is one-time and there is no way to fix it, you can ask the master to reinstall the new one. In fact, the principle of the damping shaft is to add buffer damping grease between the shaft and the shaft sleeve, and a buffer cover is matched according to different models.

Only to change the toilet seat! Take a picture of the toilet with your mobile phone, show it to the bathroom store, and they will know what type of cover to match. Remember to tell the bathroom shop that you want to descend slowly.

First, press the inside of the pin at the link between the toilet lid and the toilet bowl outward, and then lift the toilet lid upwards. This makes it easy to remove the toilet seat. If you look at it from the outside, you can't see any unloading place, and this is where you need to make special instructions to remove the toilet seat.

Take a right-angled hexagonal wrench, use the short end, insert one end of the pin from the outside, and push it hard to the inside, and the pin will come out. Then take out the pin on the other side as well. This is also an important step, and it is generally impossible to find a place to disassemble it.

The two pins that are removed are the damping system of the toilet seat. It is generally composed of an inner and outer cylinder and a viscous damping fluid sealed in the cylinder. The failure is due to the poor sealing and the leakage of damping fluid, and it is difficult to repair and can only be replaced.

After dismantling, measure the size of each part and buy the same type of pin according to the structural form. Attach the pins to the toilet lid in the reverse order in which they were removed. Then align the two holes on the pin under the toilet lid with the two small posts on the toilet bowl, press down and install it, which is very simple.

After installation, check that the toilet seat and toilet seat are able to stay in any position. As long as it can stay in any position, it means that there is no problem with the damping slow down system. The removal of this toilet seat can also be used for cleaning and hygiene.

The toilet will be dirty after a long time, and the toilet lid can be easily cleaned by removing the toilet lid according to the above method. If you don't remove it, there are many places where tools can't reach and can't be cleaned.

1.Open the toilet lid and unscrew the set screws. 2.Slide or rub the toilet lid clean with sandpaper and coat it with a small amount of tin oil.

3.Reattach the toilet seat to the Shin Shin Woo and re-screw the fixing screw with a screwdriver.

Millions of car purchase subsidies.

The damping oil leaks, which is difficult to repair and can only be replaced. Remove the original toilet damper, the pins at both ends of the connection between the toilet lid and the toilet bowl are the damping slow lowering system of the toilet seat, press the inside of the pin outward with a tool, lift it up and remove the toilet lid. Measure and observe the size and style of the removed pin, purchase the same type of pin, install a new damper, and reverse the removal operation.

Extended information: The principle of slow drop damping of the toilet seat is the slow drop damping system, which is composed of an inner and outer cylinder and the damping oil sealed in the cylinder, with a rotating shaft in the middle, which is spiral-shaped, and one end hole is large and the other end hole is small. When the toilet lid falls, it will drive the hinge to rotate, and the damping oil will be pressed from the large hole to the small hole through the spiral, because the hole is small, so it will be discharged slowly, so as to achieve the slow lowering function of the toilet seat.

If the damping system of the toilet seat is broken, you can try the following methods to fix it:

1.Replacing the damping system: The first thing you need to do is determine if the damping system is damaged or worn. If so, in this case, the damping system needs to be replaced with a new one to ensure that the soft close function of the lid is working properly again.

2.Adjustment screws: Due to prolonged use, the screws on which the lid damping system is located may become loose, causing the lid to not close effectively. Therefore, it is necessary to adjust the screws or tighten the screws with tools such as wrenches.

3.Clean the damping system: If the damping of the toilet seat is broken, it can also be due to dirt or dust. Use some detergent and paper towels to clean all parts of the damping system to ensure that they are not affected by any of the first letters.

4.Lubrication damping system: The damping system of the drum lid needs lubrication to work properly.

If the damping system is attached with dust or does not have enough lubricating oil, it may hinder the soft closing function of the lid. It is important to use some lubricant to add adequate lubrication to all parts of the damping system.

Overall, the above methods can enable you to fix the problem of broken toilet seat damping. If the problem is too serious to be solved with the above methods, then consider replacing the toilet seat.