The water heater at home can t produce hot water, but the kitchen can produce hot water

Hello, this situation can be troubled from the following three aspects:

First, the pipe from the water heater to the bathroom is clogged. Nowadays, there are many PPR pipes, and it is easy to cause pipe blockage when scalding. In addition, the rubber gasket of iron pipe or PPR pipe joint is also easy to be wrung out due to quality problems, resulting in blockage of the pipe.

Solution: Check whether the pipeline is smooth.

Second, the water discharge time is short and the pipeline is too long. Before the hot water could flow, the washing was finished.

Solution: Leave hot water for a while.

Thirdly, the cold water pressure is too high, or there is a problem with the mixing valve.

Solution: Test the cold water pressure between the kitchen and the bathroom to see if the gap is too large. Or replace the mixing valve. Many times, the mixing valve is bought as bad.

Answer: If the kitchen has checked that there is hot water, tried several times, the bathroom shower head still does not work, then the problem appears in the bathroom shower head, the hole of the shower head is relatively small, when the use time is long, it will be blocked by scale, the water will turn back, the gas equipment will not be able to hit, and there will be no hot water. After confirming that the problem is with the shower head in the bathroom, first remove the shower head and rinse it with water. Find a needle or thin wire, take the shower head to a brighter place, and use the needle or thin wire to pierce the holes on the shower head one by one, and you will obviously feel that there is a scale blockage.

When the hole in the shower head is cleaned, it can be used normally.

The water heater at home can't produce hot water, but the kitchen can produce hot water

Hello dear, the water heater at home does not produce hot water, what is the matter with the hot water in the kitchen, and it is solved according to the following methods: There are three possible situations: First, the pipe from the water heater to the bathroom is blocked.

Nowadays, there are many PPR pipes, and it is easy to cause pipe blockage when scalding. In addition, the rubber pads of iron pipes or PPR pipe joints are also easy to be wrung out due to quality problems, resulting in blockage of the pipes and reedsley. Workaround:

Check that the pipes are smooth. Second, the water discharge time is short and the pipeline is too long. Before the hot water had flowed, the wash was finished.

Solution: Leave hot water for a while. Thirdly, the cold water pressure is too high, or there is a problem with the mixing valve.

Solution: Test the cold water pressure between the kitchen and the imitation bathroom, whether the gap is too large. Or replace the mixing valve.

Many times, the mixing valve is bought as bad.

The water heater at home can't produce hot water, but the kitchen can produce hot water

If the kitchen has checked that there is hot water, tried several times, the bathroom shower head is still not good, then the problem appears in the bathroom shower head, the hole of the shower head is relatively small, when the bright type is used for a long time, it will be blocked by scale, the water will turn back, the gas equipment will not be able to hit, and there will be no hot water. After Qu Jingling guessed that it was the shower head of the bathroom, he first removed the shower head and flushed it with water. Find a needle or thin wire, take the shower head to a brighter place, and use the needle or thin wire to pierce the holes on the shower head one by one, and you will obviously feel that there is a scale blockage.

When the hole in the shower head is cleaned, don't be in a hurry to install the shower head directly, be sure to fill it with water and shake the shower head back and forth several times, the purpose of which is this. It is to clean out the scale that sticks inside, so as to avoid clogging the holes again. After the shower head is cleaned, it is time to install it and take a beautiful bath with hot water.

It's really a great trick!

Due to the long pipeline from the kitchen to the bathroom, the water pressure is too low to catch fire. Check if the pipes and showers are blocked? The kitchen can be lit because of the short pipe spacing and the sufficient water pressure!

However, there is also this situation in my family, I first turn on the kitchen water, light the shower and then open the bathroom, and then run back to the kitchen to turn off the kitchen water, so as to take a bath, check that the waterway and shower are not blocked, and change to a new gas shower.

It is mainly caused by the low pressure of the water. You first remove the shower head to see if it works. If it doesn't work, it may be caused by a clogged hot and cold water mixing valve under the shower head, and replacing it with a new one can solve the problem.

Is the faucet broken? If the water from the same water heater is hot and cold alternately, the faucet is broken!

Do you use an electric water heater? Check whether the door is closed on the mixing valve, if you buy a new one, find the manufacturer's after-sales service to open the repair, if you have passed the warranty period, you can disassemble it, the method is: first close the main valve of the water valve, open the safety valve on the cold water pipe of the water heater, release the cold water, and the water can be connected with a basin.

Then remove the hot water pipe, between the mixing valve and the water heater, and then put water into the water tank to see if the water is normal on the hot water side, and see if the mixing valve is blocked. After finishing, it will be returned as usual, and pay attention to the raw tape must be wrapped well.

1.The pipe from the water heater to the toilet was clogged. Nowadays, there are many PPR pipes, and it is easy to cause pipe blockage when scalding.

In addition, the rubber gasket of iron pipe or PPR pipe joint is also easy to be wrung out due to quality problems, resulting in blockage of the pipe. Solution: Check whether the pipeline is smooth.

2.The water discharge time is short, and the pipe is too long. Before the hot water could flow, the washing was finished. Solution: Leave hot water for a while.

3.The cold water pressure is too high, or there is a problem with the mixing valve. Solution: Test the cold water pressure between the kitchen and the bathroom to see if the gap is too large.

You can replace the shower I have hot water in my kitchen, which means that the pipeline is still open, if it has been good before, and now it can't be used, then look at the hot water pipeline, which is blocked, most likely the problem of the shower mixing valve.

Problems with plumbing and switching too

The water heater at home does not produce hot water in the shower, but the kitchen can produce hot water, which means that your water heater is good. The shower does not produce hot water, you just need to turn off the kitchen hot water faucet to get hot water, because your water heater is only four pipes, and only one faucet can be supplied with hot water, if you open two at the same time, there is water in the low position, and there is no water in the high position, right.

The water heater kitchen can have hot water and the bathroom shower has no hot water, which means that the water heater is no problem, the shower head is single open hot water and there is water out, this may be the pipe is blocked by debris, remove the shower faucet and install two angle valves to see how the effect is.

This is very easy to understand, the kitchen hot water means that the pipeline is normal, and the shower does not produce hot water, which is the water outlet of the hot water end of the mixing valve is blocked, as long as the mixing valve is disassembled to clean up the dirt at the outlet.

If it is a hot and cold water valve, it should be caused by the wrong position of the hot water and cold water valves. Hit the valve handle to the far left, and connect the cold water of half a basin of face plate (the original cold water in the outlet pipe), and the hot water should be discharged.