What are the methods for the repair of furniture wooden doors

Dust removal should be done frequently, as dust rubs against the surface of solid wood or mahogany furniture on a daily basis. It is best to use a clean, soft cotton cloth, such as an old white t-shirt or baby cotton cloth, etc. Remember not to wipe your furniture with sponges or dishwashing utensils.

When removing dust, please use a cotton cloth that is wrung out after soaking, because the wet cotton cloth can reduce friction and avoid scratching the furniture, and it also helps to reduce the adsorption of static electricity to dust, which is conducive to removing dust on the surface of the furniture. However, it should be avoided that moisture remains on the surface of the furniture, and it is recommended to wipe it again with a dry cotton cloth. Qing Fiber.

CleaningIn order to remove traces from airborne contaminants, cooking fumes, smudges from handling and residues from glazing, we recommend using a special furniture cleaner. This solvent can also help remove excess wax.

Wax regularly, every 3 months, to apply a layer of wax to the furniture. Before using polishing wax for furniture, check whether the surface of the paint layer is intact. For newer solid wood furniture, the surface dust should be wiped off with a muslin cloth first, and the stains that have been left for too long or are difficult to remove can be wiped with a cotton cloth dipped in a small amount of gasoline or alcohol.

Then use a small piece of cotton cloth dipped in an appropriate amount of varnishing wax to coat a large area, and then use a larger dry cloth to rub the wax evenly according to the circumferential block, before waxing, the old wax should be wiped off with milder non-alkaline soapy water, and the waxing should not be too dense, otherwise it will block the pores of the wood. Over-waxing can also damage the appearance of the coating. American solid wood furniture is simple and natural, dignified and elegant, but due to the change of wood moisture content, it may be deformed or cracked, so it needs special care, especially in this hot summer.

For example, it can not be directly exposed to sunlight for a long time, it cannot be too cold or extremely hot, and too dry and humid environments are not suitable for solid wood furniture. If the temperature and humidity change too much due to frequent switching on and off of the air conditioner, even qualified solid wood furniture products will sometimes deform and crack.

Daily care to avoid allowing sunlight to irradiate the surface of furniture for a long time, or it is easy to lose the balance of moisture inside the wood and cause cracks; In the drier environment of autumn and winter, it is necessary to regularly use artificial humidification measures to replenish the excessive loss of water, such as wiping furniture after wetting with a soft cloth; Maintain a good humidity, the ideal humidity is around 40, if you use the air conditioner for a long time, you can put water next to it. The temperature difference should not be too large, so as to avoid the air conditioner being turned on and off, resulting in drastic temperature changes; Avoid placing excessively hot items directly on the surface of the furniture, as this will damage the protective paint and wax on the surface of the furniture.

The popularity of the wooden door consumer market has led to the development of the entire wooden door industry, but because of its special properties of wood products, it is easy to be damp, cracked or deformed during use.

The wooden door is deformed. When the humidity or temperature in the air is too high or too low, it will have a certain impact on the wood products, and the increase of humidity in the air will improve the moisture content of the wood, if there is no corresponding treatment, it will cause the deformation or cracking of the wooden door. If there is a slight deformation of the wooden door, it can be corrected in time by manual, and if there is a serious deformation, it is necessary to immediately contact the after-sales service for return to the factory to avoid self-repair and cause serious problems and affect the after-sales service.

The wooden door does not open and close smoothly.

If there is no problem with the installation of the wooden door, and the wall is not inclined or unstable, the door can stay at any angle when it is opened, but there will be a phenomenon of automatic opening and closing of the door in daily use, such a situation occurs because there was a problem during the previous installation, and it may also be because of the problem with the wooden door hardware, so it is necessary to distinguish the source of the problem in time, if there is a problem with the installation, you need to contact the installer to correct it again, if it is a problem with the hardware, It is caused by the loose hinge, so it is okay to tighten it.

Wooden doors are blistered and degummed.

In the production or installation process of wooden doors, there will be uneven glue application, in the later use of the phenomenon of thermal expansion, so the surface will appear bulging or bulging phenomenon, do not squeeze hard in this case, otherwise it will cause veneer injury, cracks, if this situation is encountered, it is necessary to re-polish and oil in time, if the situation is more serious, it must be returned to the factory for re-order production.

Cracks or bumps in the wooden door.

If there is a slight crack in the wooden door, you can use toothpaste to repair it, apply the toothpaste to the cracked surface, apply the same color as the wooden door on the surface when it is dry, and then apply nail polish on its surface, and the cracks will disappear before a period of time.