-
Anonymous users2024-01-24Bathroom floor tiles can be laid like this:
The selection of materials can be based on the actual economic conditions, and different materials can be selected for pasting, and the ingredients will be added to the powdered binder with water in the amount of water, and the mixing ratio is 1 part water + 3 parts binder. Stir and mix the binder slurry until it is lubricated evenly, and there is no obvious lump or paste knot, and the construction slurry after stirring is allowed to stand for 5-10 minutes, and then stir slightly for 1-2 minutes, and then it can be used.
Grassroots treatment. All kinds of dirt on the wall should be cleaned up, and the site should be cleaned, especially in the foothills.
Batch wall, wall leveling.
Use a trowel to batch the wall first, and then level it with cement slurry. This process is very important to ensure that the base is flat and prevent hollowing after pasting.
Brush with waterproof paint.
The wall should be brushed with waterproof paint to prevent soaking in water after pasting, and the general height is not less than meters, and it will be slightly higher when brushing.
Find the horizontal baseline.
According to the requirements of the design paving pattern, determine the brick arrangement scheme, and use the ink fountain to play the line to reduce the construction loss.
binder on the wall.
Scrape the freshly mixed binder slurry evenly onto the wall.
Groove drawing with a serrated trowel is a point that distinguishes the new process from the old process, using the binder slurry to be smeared on the surface of the base layer to be paved, and the strip slurry combed by the serrated trowel is full and continuous.
The pre-cleaned tiles are laid flat on the adhesive slurry base layer and the tiles are flattened with a rubber hammer. During the construction process, the tile can be rotated in a small increment to make the slurry fully contact with the back of the tile. Experts recommend that the tiles that have been laid on the base layer should be removed randomly for inspection.
Make sure that the slurry is in full contact with the back of the tile.
Adjust the size of the joints according to the size of the tiles, and reserve the corresponding size of the gap between the bricks for caulking. It can be fixed with a toothpick, etc., and the adhesive has a certain degree of adjustability, and the size of the seam can be adjusted.
It is recommended to find a professional decoration company, and there may be flaws if you decorate it yourself.
-
Anonymous users2024-01-23The kitchen and bathroom should be paved with non-slip.
du, not easy to stain, easy to clean the floor tiles, paving workers should be in a waterproof place.
After the height of the floor is solidified, the finishing of the ceiling and wall façade is completed and the bathtub and cabinet are installed. The details are as follows: (1) Pop up the longitudinal and transverse reference lines, which are required to be at an angle of 90 degrees or 45 degrees with the door frame.
(2) Remove floor tiles that do not meet the quality requirements such as large color difference, cracks, missing corners, glaze damage, warping, etc. (3) For each row of shops, the longitudinal inspection must be carried out with a ruler or a line. Transverse straightness and surface flatness.
(4) Non-whole bricks should be laid out of the line of sight. (5) The cement slurry for laying can be pure cement or 1:2 spun pulp.
The back of the brick should be full and full when the ash is batched, and it should be patted with a rubber hammer after paving. (6) When the cement has not solidified after the floor tiles are laid, protective measures must be taken, and gravity should not be borne on it to prevent high and low dislocation.
-
Anonymous users2024-01-22Looks simple and does.
It's hard to copy. First of all, do a good job of waterproofing, do a good job of waterproofing and wait for two days to pour some water, and see if it leaks to the next layer of you. Construction can be done without water leakage.
Sticking to the bathroom floor mainly pays attention to the problem of drainage, that is to say, the bathroom floor can not store water, and all the water must flow to the place where the floor drains. Therefore, the bathroom floor generally does not give you a level surface. THE BATHROOM IS GENERALLY A SMALL FLOOR OF 30 CM * 30 CM.
It is better to choose the kind of non-slip one. Generally, when you go to the bathroom to take a bath, you will bring some water when you urinate and poop. Typing hard to give some points.
-
Anonymous users2024-01-21It's too complicated, if you want to learn, find a master to take you.
-
Anonymous users2024-01-20How to tile the bathroom: 牋牋牋.
How can I tell you this.
Spread horizontally and vertically. >>>More
Yes, it will raise the floor, and you have to consider the difference in the height of the floor in the final hall. Generally, hairing, and then interface agent, you can apply tiles.
The color of the tiles in the bathroom needs to match the color of the three major pieces of the bathroom, so as to show a good overall effect. Generally speaking, the color selection of the three major pieces of sanitary ware is consistent, and research shows that it is best not to have more than three colors in a room, otherwise it is easy to dazzle. If the color of the three major pieces of sanitary ware is dark, the color of the tile can be matched with light color and similar color; If the color of the three major pieces of sanitary ware is a light and cool color, then the color of the tile is best to choose a dark or light warm color to match. >>>More
It's beautiful, it's atmospheric, it's expensive, and it's a waste to use.
The joints of the 800 floor tiles in the living room are as follows: the joints can be adjusted between 2-3mm, and at the same time, in order to avoid wasting materials, the corners are used as many bricks as possible, which is both beautiful and saves time and money. >>>More