-
Anonymous users2024-01-24Hello, if you are using energy-saving lamps with starting devices, check the starting device, if not, then see if the electrical appliances are consistent with the corresponding power supply voltage, if not, it may be that the voltage is too high to cause damage to the lamps, the specific situation is not on the spot, it is difficult to answer accurately. It is recommended to find an electrical maintenance technician to investigate and find out the cause on the spot, so as to avoid other property losses caused by damage again
-
Anonymous users2024-01-23The ceiling at home does not light up after a flash, it may be that the bulb is broken, or it may be caused by poor wire contact. The third reason may be that the power is lost due to tripping.
-
Anonymous users2024-01-22The main reasons why the chandelier does not light up after flashing are: the lamp tube is damaged, and the lamp tube does not light up after flashing. The upper inverter is faulty. Ballast failure. The line is faulty, and the related line is burned out instantly. The switch is faulty, the switch is in poor contact, and it cannot be stabilized in the closed state after closing.
Hello, if you are using an energy-saving lamp with a starting device.
Please check the starting device, if not, see if the electrical appliance used matches the corresponding power supply voltage; If not, it may be that the voltage is too large and the lamp is damaged, and it is difficult to accurately determine the specific situation when you are not on site. It is recommended that the cause be identified by the electrical maintenance technician on site to avoid other property losses caused by redamage.
If there is no trip.
The reason is that the bulb is broken.
1 bulb is broken, 2 drives.
It's broken. Either the contact is bad or broken, it depends.
-
Anonymous users2024-01-21The chandelier in the living room at home flashed and didn't light up for a while, what is the problem? If the chandelier in your living room flashes a little, it won't come on. It should be that the light is flashing, and you can change it to a new one and it will work.
-
Anonymous users2024-01-20How long did the chandelier take? Is it new? There is a certain total use time for bulb products, and it will break down when the time comes.
-
Anonymous users2024-01-19It's broken, it's 、、、
-
Anonymous users2024-01-18Summary. The main reasons why the chandelier does not light up after a flash are:
The lamp is damaged, and the filament burns out after flashing, causing the lamp to not light up.
The starter is faulty.
Ballast failure.
The line is faulty, and the relevant line flashes and burns out.
The switch is faulty, the switch is in poor contact, and it cannot be stabilized in the closed state after closing.
The chandelier in the living room at home flashed and didn't light up for a while, what is the problem?
><> wait a minute.
The main reasons why the chandelier does not light up when it flashes are: the lamp tube is damaged, and the filament burns out after flashing, causing the lamp tube to not light up. The starter is faulty.
Ballast failure. The line is faulty, and the relevant line is burned after flashing. The switch is faulty, the switch is not well connected, and it cannot be stabilized in the closed state after closing.
-
Anonymous users2024-01-17Summary. Hello dear, the main reasons why the chandelier does not light up after flashing are: the lamp tube is damaged, and the filament burns out after flashing, causing the lamp tube to not light up.
The starter is faulty. Ballast failure. The line is faulty, and the relevant line flashes and burns out.
The switch is faulty, the switch is in poor contact, and it cannot be stabilized in the closed state after closing.
The chandelier in the living room at home flashed and didn't light up for a while, what is the problem?
Hello dear, the main reasons for Li Ji when the chandelier flashed were that the lamp was damaged, and the filament burned out after flashing, causing the lamp to not light up. The starter is faulty.
Ballast failure. The line is faulty, and the relevant line flashes and burns out. The switch is in poor contact, and it cannot be stabilized in the closed state after closing.
Every time. If you are using energy-saving lamps with starting devices, check the starting device, if not, then Zenqiao to see if the electrical appliances used are consistent with the corresponding power supply voltage, if not, it may be that the voltage is too high, resulting in damage to the lamps, the specific situation is not on the spot, it is difficult to answer accurately. It is recommended to find an electrical maintenance technician to investigate and find out the cause on the spot, so as to avoid other property losses caused by damage again
-
Anonymous users2024-01-16The main reasons why the chandelier does not light up after a flash are:
1.The lamp is damaged, and the filament burns out after flashing, causing the lamp to not light up.
2.The starter is faulty.
3.Ballast failure.
4.The line is faulty, and the relevant line flashes and burns out.
5.The switch is faulty, the switch is in poor contact, and it cannot be stabilized in the closed state after closing.
-
Anonymous users2024-01-15Hello, if you use a copy of the energy-saving lamps with a starting device, check the starting device, if not, then see if the use of electrical appliances and the corresponding power supply voltage is consistent, if not, it may be that the voltage is too high to cause damage to the lamp, the specific situation is not on the spot, it is difficult to answer accurately. It is recommended to find an electrical maintenance technician to investigate and find out the cause on the spot, so as to avoid other property losses caused by damage again
-
Anonymous users2024-01-14If it doesn't trip, the reason is that the bulb is broken
-
Anonymous users2024-01-131 The bulb is broken, 2 the driver is broken.
-
Anonymous users2024-01-12Either it's a bad contact or it's broken, depending on the situation.
Check the total electric switch first, there is a sub-switch in it Is it jumping, the kitchen, living room, and bathroom may be a line of electricity, to check the electric combustion in the living room, as long as the living room is lit, I think the others should also be able to light up.
During construction, the power supply distributed everywhere is divided into open lines, your balcony and the bedroom is a power supply, this power supply depends on your situation is to lead to the power cord there is a virtual connection or the wiring is not tightened, or the air switch of this road may be damaged, long-term this will burn out the line, the damage to the refrigerator and air conditioning is also very large, very serious, deal with it quickly.
You woke up in the middle of the night and saw the indicator light on the plug, although it was not on when there was light, but when it was very dark at night, you suddenly saw that the light was very bright.
It should be caused by the failure of the living room lamp and a short circuit causing the room circuit breaker to trip, it is recommended to check the fault of the living room lamp and find the fault point for maintenance.
Do you see if someone else's house has electricity? If someone else's home doesn't have it, you need to find a property. If someone else has electricity in their house, you turn off the power switch. Then unplug all appliances. All. Push it up again. Look.