-
Anonymous users2024-01-24Installation method: 1. Expansion bolt installation method.
1. First measure whether the size of the opening is consistent with the size of the door frame, if it is smaller than the size of the door frame, the excess gray skin should be removed from the gentle width.
2, the anti-theft door opening position upright, so that the frame decorative edge and the wall are tightly attached, according to the frame side of the 6 holes after the mark, the door frame is moved out of the hole, and then with a drill bit drilling, the door is pushed into the hole, driven into the M10 steel expansion bolt, tighten the nut with a socket wrench.
Second, which method is there to fill cement.
1. If the frame is polyurethane foamed, there is no need to fill cement; If there is no polyurethane foam frame, it must be filled with cement, so that there is no hollow in the security door and the edge, and the installation is more firm.
2. Before filling cement, use a paper pad between the door frame and the two sides of the door leaf, and close the door for filling.
3. When filling cement, do not squeeze too much, so as not to deform the door frame and affect the opening.
4. Remove the paper pad after filling the cement for 6 hours, open the door, and clean the cement at the keyhole of the door frame.
-
Anonymous users2024-01-23Tools Raw materials.
Impact hammers, socket wrenches, levels, wire sags, tape measures, hammers, screwdrivers, iron files, steel chisels, cutting machines, hacksaws, etc.
Expansion plugs with a diameter of 10-12 mm.
Step Method.
Measure the size of the door opening first, and determine the opening direction according to the stairway. The size of the door opening should be larger than the size of the installed door, and leave a certain margin (approximately, convenient for debugging and correction during installation.
Correct the door opening, the size of the door opening does not meet the requirements, and must be cut and leveled with iron gongs, steel chisels, cutting machines and other tools to meet the installation requirements.
During installation, put the door into the door opening, plug it tightly with a Paiju early wood bolt around it, correct the horizontal and vertical degrees, debug whether it is flexible to open, and then open the door leaf, drill the installation hole through the door frame installation hole with an electric hammer, and fasten it with an expansion bolt one by one.
The depth of the expansion bolt into the wall should be 5cm, and the drill bit of the impact hammer should match the size of the expansion bolt. During the installation of the project, the owner or the builder shall mark the 50cm horizontal line or 100cm horizontal line, and the user shall determine the height of the floor tiles or floor for individual installation. After the door is installed, a certain amount of cement mortar (generally more than 70%) needs to be poured into both sides of the door frame, and the mortar for repairing the wall is completed by the user himself.
-
Anonymous users2024-01-22Installation Method:
1. Expansion bolt installation method.
1. First measure whether the size of the hole is consistent with the size of the door frame, if it is smaller than the size of the door frame, the excess gray skin should be removed.
2, the anti-theft door opening position upright, so that the frame decorative edge and the wall are tightly attached, according to the frame side of the 6 holes after the mark, the door frame is moved out of the hole, and then with a drill bit drilling, the door is pushed into the hole, driven into the M10 steel expansion bolt, tighten the nut with a socket wrench.
Second, the method of filling cement.
1. If the frame is polyurethane foamed, there is no need to fill cement; If there is no polyurethane foam frame, it must be filled with cement, so that there is no hollow in the security door and the edge, and the installation is more firm.
2. Before filling cement, use a paper pad between the door frame and the two sides of the door leaf, and close the door for filling.
3. When filling cement, do not squeeze too much, so as not to deform the door frame and affect the opening.
4. Remove the paper pad after filling the cement for 6 hours, open the door, and clean the cement at the keyhole of the door frame.
-
Anonymous users2024-01-21Security Door Installation Steps:
1. Measure the size of the door opening, pay attention to the size of the door opening should be larger than the size of the security door, and at the same time, you need to leave a gap of 1 to 3CM to facilitate better adjustment during installation.
2. Install the anti-theft door, put the door into the door opening, fix it with wooden bolts around it, adjust the horizontal and vertical degree of the anti-theft door, test the flexibility of opening the door, and install the installation hole on the door frame with an electric hammer.
-
Anonymous users2024-01-20Anti-theft door installation tutorial, sharing fast and good skills, all dry goods worth collecting.
I used to be an apprentice plumber.
You don't ask for anything. >>>More
Yes! I think Kincaid's security door is pretty good. It is an old brand, and the anti-theft coefficient of their anti-theft door is Class A, with thickened door panels, which is safe and more noise-isolating.
Dressers can be divided into two types: free-standing and combined. The freestanding type means that the dresser is set up separately, which is more flexible and casual, and the decorative effect is often more prominent. Combined is to set up the dresser in combination with other furniture, this way is suitable for small families with little space, assemble this product need to bring a Phillips screwdriver, according to the assembly instructions attached to the product to install correctly, one person can complete it alone; This product can be disassembled and used repeatedly, and can be wiped with a cloth when cleaning.
I think it's all done with on-site installation! It's easy to do that way, and it's sure to be beautiful if you do it well in advance. It's all mass-produced.
1. Replacement steps: 1. Remove a piece of the gusset next to the lamp (with a suction cup or a sticky hook); 2. Then take off the lampshade and press the lamp tube of the same model; 3. Press the lampshade and the removed gusset. 2. Precautions: >>>More