-
Anonymous users2024-01-24It can't be used for 24 hours because you have to wait for glass glue.
It is completely dry, if it is used it may cause the glass glue to not dry completely and the toilet is not installed firmly.
Before installing the toilet, you should carefully read its instructions and construct according to the requirements. Code for Construction of Residential Decoration and Decoration Engineering
stipulates that sanitary ware must be tightly connected with water inlet pipes and sewage outlets, and there shall be no leakage;
Toilets. Apply expansion bolts.
Fixed installation, and sealed with lime or silicone glue, the base shall not be cemented mortar.
Fixed. This not only avoids cracks in the toilet caused by dry cracking of cement, but also facilitates repairs in the event of a problem in the future.
-
Anonymous users2024-01-23After installing the toilet, it cannot be used for 24 hours, because the glue has not been completely solidified, if the toilet is used, the water will destroy the stickiness of the glue, and the toilet base will not be firmly bonded and easy to loosen. Sewage is also prone to seepage out.
-
Anonymous users2024-01-22This may seem like a small problem, but it's actually a big deal that can't be ignored.
If the glue is used before it solidifies, it may cause the toilet to separate from the floor, and in long-term use, the toilet will be displaced, which will lead to the displacement of the toilet drain pipe and damage the sewage pipe on the upper part of the ground. Negative consequences.
-
Anonymous users2024-01-21Well, this one! Our house is used for the day!
-
Anonymous users2024-01-20Summary. A Hello, dear, the toilet can not be used for 24 hours after installation, because the glue has not been completely solidified, if the toilet is used, the water will destroy the adhesive of the glue, and the toilet base will not be firmly bonded and easy to loosen. Sewage is also prone to seepage out.
Why can't the toilet be used for 24 hours after installation, and what will be the problem if it is used
A Hello, dear, after installing the toilet for 24 hours can not be used, because the glue has not been completely solidified, if you use the Ma Dayun bucket Chang imitation chop, the water will destroy the adhesive of the glue, the toilet base is not firmly bonded, easy to loosen. Sewage is also prone to seepage out.
Is it an outer layer of glue? Or the glue from the flange? But doesn't the installer also have to perform a flush test? Isn't that a contradiction?
Hello, dear, 1Use Huitian 7901 gasket remover to remove the residual original liner and oil stain 2, clean the flange with Huitian 7551 cleaning agent to match the surface 3, which Yubi will apply Huitian silicone rubber type plane sealant on one surface to form a continuous closed rubber ring 4, close the flange to Li Juzhun within ten minutes, pressurize and tighten the screw 5, wipe off the glue that is squeezed out 6, Huitian silicone rubber type plane sealant absorbs the moisture in the air and begins to cure and dismantle (from the surface and inside). The curing speed depends on temperature, humidity and bond line thickness, and generally takes 24 hours to cure completely.
Could this be? People in order to facilitate the power saving, so set up, so that you can see if you can heat 24 hours to see the manual.
As long as the sanitary ware in the water tank can be used normally, it can be opened 24 hours a day. Water the toilet will only be flushed when it is flushed.
All night long.
Synonyms] night and day. >>>More
It may be that the upstairs toilet or the water pipe is broken and keeps running water, and there is also the fact that the bathroom pipe in your home is not covered with soundproof cotton.
The power supply of a notebook is generally 65W, which means that the maximum power of a notebook generally does not exceed 65W. Calculated at 65W, 65W*24H=1560WH, that is, 1560Wh = kWh (kWh), the maximum power consumption per day.