What should I do if the kitchen drain pipe is blocked?

Wear rubber gloves first, as the next thing you need to do is be dirty and oily, and the raw edges of the wires and pipes are likely to scratch the skin on your hands. Wearing gloves is the best protection.

3.This household manual dredge is a relatively hard wire ring structure, the steel ring on the head is relatively sparse, and the back is more dense. We first take out the plastic pipe at the position in step 1 from the sewer pipe, and then connect the head of the tool to the bottom of the main pipe.

4. It is generally easier to enter the first section, and the spring tube has been deepened.

5.Dig deep to a certain extent, you will find that the spring steel wire can no longer go in, how to poke it can't work, this is to the position of the blockage, don't be in a hurry to poke, if there is a "pipe pass" at home can be poured into half a bottle to a bottle in, if there is no pipe through, you can also use "kitchen heavy oil cleaner to replace, if there is really none, use dish soap to make do." This step mainly relies on chemicals to break down the blockages in the pipes.

And this blockage is generally bonded together by grease, so dish soap also has a certain effect.

6.After pouring in the chemical agent, wait for 10-20 minutes, and then pour a pot of boiling water into the pipe, at this time, you will hear the sound of gas in the originally blocked pipe.

7.At this time, two people are needed to operate together, one person holds the spring steel wire, and the other person shakes the handle behind it, and after shaking it a few more times, the steel wire will continue to pass down. It may not be easy to operate at first, take your time, shake it a little longer, and it will be through.

8.After it is passed, all the wire springs should be inserted into the pipe, and a person will shake the handle at the mouth of the pipe. Shake a little longer to make sure the debris in the tube is broken. At this point, the main pipeline below is considered to be unobstructed.

The above is the solution to the blockage of the kitchen sewer pipe, in addition, after all the installation, let go of the faucet and let the water flow for a while, observe where there is still a leak, if the water leaks, then uninstall and check it. There are two reasons for the water leakage: one is that the rubber cover is not installed properly, and the other is that the screwed position is slippery.

You can wrap the raw meal tape when you screw it, and it will be much denser. Old Yin's sea cucumber tips.

1. The kitchen sewer pipe is used more frequently, it is inevitable that there will be a phenomenon of blockage, this happens, first to judge the reason, if it is because of some sundries blocked, you can find something like iron wire to get the dirt out, if not, and the house has lived for a short time, you can find a decoration company, because this is a quality problem. If it is a hidden project, it is free of charge for five years.

2. If you find that the kitchen sewer pipe is blocked, the first thing to do is to close the water pipe to avoid more stagnant water, and never try to flush the impurities down through the water. Let's take a look at what is blocking the kitchen sink, generally the sewer pipes at home are blocked by greasy, so pour a pot of boiling water into the sewer pipe first, and then dredge the effect will be better, if the drainage is still not smooth, use a wire to penetrate down, and deal with general small problems from these two aspects can be solved.

3. When there is no obvious blockage in the drainage pipe of the pool or washing tank, the overflow hole can be blocked with a damp cloth, and then the sludge can be removed with a wrench. If you can't remove a blockage from the sink or sink drain using a wrench, you can place a bucket at the drain bend and unscrew the elbow to remove the blockage.

4. Most of the places where the kitchen sewer pipe is blocked are U-shaped bends, if it is a sewer pipe with sewage screws, it is easy to do, and it is easy to unscrew it directly, but before treatment, a sewage basin should be placed at the bottom to avoid staining the cabinet. After unscrewing, use a steel wire to pass both sides, and it can usually be solved quickly. If it has not been solved, you can remove all the sewer pipes, unscrew all the plastic connections, rinse them, remove the impurities inside, and then assemble them in turn, and then solve the problem.