The bottom of the toilet is leaking

It is an overflow caused by a clogged sewer.

Reason: The toilet bowl and the floor tile are usually bonded with glass glue or white cement, which only plays a role in bonding, not completely sealed, when flushing, due to the blockage of the sewer pipe, can not quickly flow out of the toilet water, resulting in the benefit to the inside of the toilet, and then from the toilet and the floor flow.

2. Remove the toilet and dredge it again.

If it's a leak at the bottom, it depends on what company you used for renovation at the time.

1. If it is installed in a specialty store, it is usually padded with a sealing ring inside, and the toilet is placed with glass glue around it; Tools to prepare: utility knife, (if you need to disassemble the angle valve) water adhesive tape, wrench, glass glue and glass glue gun. A special seal for the toilet bowl (if it is removed, it needs to be replaced).

2. If it is a decoration of plumbing and electrical tooling, white cement is usually used; Tools to prepare: flathead screwdriver (used to eliminate the original white cement), white cement (when reloading, first mix the water at the bottom of the toilet, then put the toilet seat on it steadily, and then use the mixed white cement to seal the toilet footsteps in a circle, and then use it when it is dry.) Be careful not to let the white cement fall into the pipe, otherwise it will cause the pipe to be blocked.

If there is a problem, it needs to be removed and cleaned and replaced, if it is still leaking, it needs to be replaced with a new scoop. If the scoop is fine, see whether the rubber pad at the sink hose interface is aging, and replace it with a new rubber pad in time.

1. The surrounding area of the toilet seat is very clean, and the residual bacteria are very many, which is due to the fact that when flushing the toilet, it will cause the stains in the toilet bowl to splash on the toilet seat, if it is not cleaned up in time, when people use it again, the bacteria will stain the surface of the human skin, thus causing various diseases, so every time the toilet is used, the toilet seat must be cleaned.

2. After the toilet is used, it needs to be flushed to dispose of the internal excrement, and if there are yellow spots left in the toilet, you must brush it off with a brush, otherwise after a long time, the yellow spots will solidify, and it will become very troublesome to clean up. Also, be sure to close the lid of the toilet bowl when flushing.

3. Around the toilet, it is generally necessary to place a garbage can, so that the waste paper used daily can be thrown into the trash can, which can effectively place the toilet to be blocked. However, we must develop a good habit of cleaning out the bags in the trash can every day, otherwise it is easy to breed bacteria, which will affect the use.

It is a drain hole that is not in place. Or the flange seal used for the original installation is leaking. However, there is also a possibility that there are holes or cracks in the bottom of the toilet itself, which is relatively rare.

But there are. The main thing is that when the toilet leaves the factory, it has been repaired. The mended thing fell out.

For the first one or two problems, you can replace it with a new flange ring, including reinstalling the toilet. Now don't hit the glass glue. Repairing with plastic steel mud will harden and fix the toilet bowl and anti-leakage function.

It will not turn black and moldy. You can ask me if you need to. Or go to Taobao to search Haocheng sanitary ware.

The initial decoration of the bathroom is very important, because the decoration at this time should take into account the problems of waterproof, odor prevention and so on. Many people find that soon after installing the toilet, it will smell, why?

This is what my toilet base looks like after it is disassembled, it has been smelly for three years, so disgusting.

Let's talk about the four main reasons why the toilet stinks:

1. The quality of the toilet product itself is poor, and the void of the toilet is large, and there are a lot of stains left in it.

2. The project was not done well during installation, and the flange ring under the toilet was not sealed.

3. The base of the toilet is not sealed, or the glass glue of the base is not done.

4. There are some firing holes in the toilet base, but these holes are not sealed, and the smell comes out.

The solution of Article 1 is that we can only buy toilet products with better quality, and we can buy better glazed products.

Article 2 suggests that you should use glass glue for the flange, and when you use this kind of glue, you should use water to flush it with water to see if there is any leakage.

Article 3 Most of the toilets that we sleep on now do not use cement to seal the bottom, most of them use glass glue, and we must pay attention to not break it when playing glass glue, and we must play it completely in a whole circle.

The base of the fourth toilet bowl usually has two or three firing holes, and many people don't know about it. Some merchants do not treat the product when it leaves the factory, so after you install it, the smell of the toilet will flow out of the holes here, so we have to seal these holes.

This small suggestion, in fact, installing a toilet is a kind of technical work, even if the worker is skilled, it is not as good as installing it yourself. When you buy a product, you can also let the merchant package install it, so that you can save the installation fee.

It should be noted that if you want to lay the floor tiles and then install the toilet, this is the correct installation sequence.

It is that the rubber mud and PVC pipe at the bottom of the toilet bowl will leak if they are not sealed properly, and the glass glue around the bottom of the toilet bowl is not well played.

Disassemble and reassemble, replace with new cement, and lay glass glue.

Dismantle it, buy a new flange, re-fix it, and make glass glue There is no other way to get my house yesterday.

Loosen the fixing screws, turn the toilet over to the bottom, wipe the leaking place, and beat the glass glue. Use after 24 hours.

waterproof glue, or replace it with a new one.

It is best to install the toilet from scratch.

Caused by installation errors or broken flanges.

The specific steps are as follows:

1. The bottom edge is leaking, which may be caused by installation errors or broken flange rings, it is recommended to remove the toilet, reinstall it, or replace the flange ring.

2. If it is caused by the poor sealing of the bottom of the toilet and the floor tiles, that is, the glass glue is opened, it is recommended to remove the old glass glue and re-enter the high-quality glass glue seal.

3. If the bottom of the toilet is cracked and leaking, the crack is not large, it can be filled with colloid, if the crack is large, it is recommended to replace the toilet.

4. Toilet leakage, in addition to the quality of the toilet itself, it is also possible that the quality of the water valve pipe is not good, and it is damaged, causing water leakage. In addition, if the drain valve is not tightly sealed, it will also cause the toilet to leak.

If the bottom of the toilet is leaking, it may be the following reasons:

1.Loose screws: The screws at the bottom of the toilet bowl may come loose, causing water to leak out of the bottom. Screws can be tightened using a wrench.

2.Aging seals: The seals at the bottom of the toilet bowl can age or break, causing water to leak from the bottom. The seal needs to be replaced.

3.Cracked toilet bottom: If the bottom of the toilet is cracked, water will leak from the bottom. The entire toilet bowl needs to be replaced.

4.Clogged drains: If the drains are clogged, water will overflow from the bottom of the toilet. The drain needs to be cleaned.

If you are not sure how to fix a leak at the bottom of your toilet, it is advisable to contact a professional plumber to have it checked and repaired.