How long does it take for a new toilet to be used?

You can do it at any time, as long as your butt doesn't move!

Of course, it depends on the skill of that comrade

We can use it without glue and it doesn't leak at all.

It should be used after 24 hours, because it should be firm after the glass glue has dried thoroughly, otherwise, it will leak. It is recommended that you install the toilet with sand and cement for the best, strongest and more durable. That's how my house is installed.

After the toilet is installed, it should be flushed and debugged immediately, and all aspects are normal to be qualified. How long it can be used is for the base sealed with silicone glass glue, the temperature is different, the required time is also different, and the flushing is no problem.

1. The newly installed toilet can be used in about a day.

2. After the new toilet is installed, you need to use sealant at its base and wait for a day or so for it to dry.

3. However, it should be noted that if the toilet base is pasted with cement mortar, it is necessary to wait for about seven days to let it dry thoroughly to avoid the reduction of the sealing effect.

The above is all the content for how long a new toilet can be used, do netizens understand?

Hello! Generally, the sealant is dry after the installation and water test, or the cement of the base can be used after you dry for 48 hours. During the period, pay attention to the water protection and maintenance of the base cement, and pour some water on the periphery of the base. It is best not to apply force to the toilet bowl during maintenance.

If it is fixed with expansion wire, it can be used at any time, and the glass glue can only be used after the glass glue is dry.

Generally installers will say 24 hours, or 48 hours. In fact, the workers are skilled. It can be used in 3-5 hours after loading.

As long as you sit down honestly!

If you apply glass glue, it is best to use it after 48 hours.

If it is not glass glue, it is generally fine for 24 hours.

If you look at the instructions for the sealant, you can see how long it dries, and it's usually 24 hours, but it's fine after eight hours.

This mainly depends on the brand, and the most important thing is the machine inside.

After a day, it was ready to use. Don't use it right away.

1. Before choosing a toilet on the market, first determine the size of the water in the seat (i.e., the distance from wall to wall). Before installation, please make sure that the product accessories you choose, completed, please carefully review this manual and learn about some products.

2. Determine the height of the drain according to the condition of the toilet and cut off the rest of the part. The goal is to make the plumbing and toilet bottom more consistent. Start by using a hacksaw or cornea for the sewer according to the horizontal height of the centimeter, because the flange of the toilet bowl is soft.

If it is not centimeters high, there may be water seepage problems, and centimeters are more tightly fitted.

3. Measure the pit distance. Before choosing a toilet, first determine the size of the water inside the house, that is, the distance from the wall to the water. When using a toilet, if you want to decorate the tiles, you must measure the pit distance after applying the tiles. Otherwise, the toilet will be bought back and cannot be installed.

4. Install the flange ring provided with the toilet at the drain. Remember to press hard to ensure the compaction of the flange ring and toilet drain. Place the flange on the toilet drain.

Then carefully align the lower hose and lower it smoothly. At this point, the wall of the sewer pipe is inserted into the viscous clay of the flange for sealing.

5. After the water test is completed, start to install the cover.

6. Glue around the toilet, this step is also very important, not only to stabilize the toilet, but also to prevent the smell of the net from being released from the toilet. Therefore, we will not only fight, but also four whole weeks. At the intersection of the toilet bowl and the outer surface of the floor, since the toilet bowl and the floor are not one, a joint seal transparent sealant can be used for agitation, and the outer opening of the toilet bowl is sealed to maintain the integrity of the floor.

Some bathroom water can clog around the toilet bowl. NOTE: IF YOU NEED TO INSTALL THE SET SCREWS, FIRST APPLY A SPECIAL SEALANT INSTALLED IN THE TOILET BOWL EVENLY ON THE OUTSIDE 2CM OF THE TOILET BASE.

The drain of the toilet bowl should be pulled towards the center of the drain. Expansion bolts are located on the left and right sides of the toilet, remove the toilet, punch holes and raised bolts.

7. Install or debug the water tank accessories.

8. After installing the toilet, wait until the glass glue (putty) or cement mortar has solidified before releasing water. The curing time is usually 24 hours.

Newly installed toilets can only be used for two or three days when the weather is cold in winter, and one day is fine when the weather is hot.

You can use it immediately, because the main reason is that you are afraid of flushing to destroy the solidification of the glass glue, and the speed of the glass glue is very fast, and there is no problem!

Mainly wait for the glue to dry, generally the weather is good for 1 hour, and the slowest does not take 1 day, rest assured. I get that glass glue every day, I've never seen it so slow.

The newly installed toilet is ready for use after 24 hours of ventilation in the toilet.

Toilet installation a sewage pipe inspection.

The first step in installing the toilet is to check the dredging of the sewage pipe, so that the installation of the subsequent toilet will play the most fundamental guarantee, and the inspection of the sewage pipe is to prevent the blockage of the pipe after the installation of the toilet, resulting in the problem of frequent congestion of the toilet, which is the first point of the installation method of the toilet that needs to be paid attention to, and must not be greedy for progress and ignore this critical link, so that once the toilet is congested in the future, it is too troublesome to find someone to repair.

Toilet installation two toilet options.

After checking the sewage pipe, the next step is the purchase of the toilet, according to the size of the sewer to choose, so that the installation of the toilet is more trouble-saving and labor-saving, in the process of purchasing, we should pay attention to whether the accessories of the toilet are complete, especially the installation method of the toilet, this must be noted, carefully control the instructions when installing, so that there will be no problems.

I specialize in repairing toilets in Xi'an, and there is no problem after a week, and the glass glue is completely dry after a week.