How to do waterproof leakage repair in the bathroom?

Waterproofing and leakage repair in the bathroom is a more important problem, because moisture is easy to penetrate into the inside of the wall, causing the wall to peel and fall off, and in serious cases, it will also affect the downstairs neighbors. Here are some methods and steps to repair waterproof leaks in the bathroom:

1.First of all, it is necessary to determine the location of the water leakage, which is usually in the toilet, shower, sink, etc. You can use a small hammer to knock on the wall quietly, and the place where you find that the sound is abnormal is the leak.

2.After determining the location of the water leakage, it is necessary to clean up the debris and residue on the wall and floor to ensure the cleanliness of the water leakage location.

3.The third step is to repair the leakage, which can be repaired with cement until the leak is completely covered. You need to wait until the cement is dry before applying a layer of waterproof paint, and you can buy waterproof brush paint or roller paint on the market at any time.

4.After repairing the leak, the entire bathroom floor and walls need to be waterproofed. You can buy waterproof paint or waterproof membrane on the market for covering, you need to pay attention to avoid loopholes when brushing the paint, and pay attention to the tight docking when the membrane.

5.The final step is to wait for the waterproofing material to dry and then conduct a water test to check if the restroom is truly waterproof. It is necessary to pay attention to the water test to evenly moisten the entire bathroom, not only the leaky area.

In general, it may take time and patience to repair leaks in the bathroom, but it must be done well to ensure the comfort and safety of the living environment. If you are unsure about the operation, seek professional help.

1. Wipe off the water stains and clean the dust on the surface with a brush.

2. Spray waterproofing agent on the leaking place, and then make up for it with caulking material after it is dry.

3. Don't forget to do a good job of waterproofing the eggplant sock pie, you need to wait for a day before you can get watered.

If the leakage area is large and the impact is widespread, then you need to start from the bottom.

The bathroom is a perennial water flow area, if the traditional method of waterproofing and leakage repair cost is relatively high, it is recommended that you use modern more advanced technology for toilet waterproofing. The modern waterproof leakage repair method is relatively simple, time-saving, but also labor-saving, the leakage filling effect is better, relatively fast, it can be said that it is an immediate effect, a leakage, once and for all.

The company has introduced international advanced high-pressure grouting waterproof technology and equipment, high-quality materials and modern management mode, specializing in kitchen leakage repair, bathroom leakage, exterior wall leakage, floor leakage, balcony leakage, roof leakage, canopy leakage, window sill leakage and other waterproof leakage repair engineering business.

In order to ensure the quality of construction, it is necessary to conduct on-site investigation before the construction of plugging, find out the on-site construction situation, analyze the causes of water leakage, find out the width, length, depth and penetration of water leakage parts, cracks, cracks or perforations, and understand the water leakage situation in rainy and sunny days, measure the flow rate and flow rate of water leakage, etc., through full investigation, correctly draw up the plugging plan, and make various preparations.

The advantages of high-pressure grouting waterproof plugging construction.

1.The pressure is high and stable and reliable, which can allow the chemical slurry to completely enter the deep micro-cracks of the concrete structure, and the water-stopping effect is good.

2.The grouting technology is mature, the variety is complete, and the production of single-component finished products has basically been realized, without on-site deployment, the quality is stable, and it can be used when the barrel is opened. The slurry is chemically resistant, non-toxic, environmentally friendly, and permanently waterproof after curing.

3.The construction process is simple and easy to implement. The construction speed is fast, and the water-stopping effect is immediate, once and for all. The labor intensity of workers is small, and the construction efficiency is 5 to 10 times that of traditional construction methods, which cannot be compared with traditional methods.

4.The construction is not limited by the season and weather, and can be used for various projects, including overhaul, emergency repair projects, and drinking water projects.

Chongqing Ruide Company is a modern high-tech enterprise. The company pays attention to scientific research and development, and has established a long-term close scientific research cooperative relationship with the first fighter of environmental protection in China's decoration industry, the founder of anion home improvement pollution control products, and the founder of anion healthy flooring.

What benefits can negative ions bring to our lives?

Purify the air - negative ions can neutralize the positive charge of formaldehyde, ammonia, benzene and other harmful gases in the room, reduce the harmful substances in the air, improve the freshness of indoor air, and have the functions of dust reduction, antibacterial, deodorization and other air purification;

Antibacterial function - it can kill or inhibit the reproduction of bacteria, viruses and molds in the room.

Health care effect - when the negative ions in the air reach more than 700 cubic meters, it has a health care effect on the human body. When it reaches more than 1000 cubic meters, it has a therapeutic effect.

High-pressure grouting waterproof leakage repair technology and negative ion environmental protection cleaning is the future development trend of the cleaning industry, Ruide company dares to be the first in the world, the courage to open up, dare to innovate for the majority of owners to create a healthy, clean work, life in the integration of the beautiful environment, is our unremitting efforts to pursue!

Before, my bathroom was always leaking, and it was even more serious after it seeped downstairs, and I had no choice but to find a waterproof leakage repair company, but it was still leaking the next day. I was speechless, and finally found a Qianrui waterproof company through a friend's introduction, at first I didn't dare to trust the quality, but my friends strongly recommended it, I tried it, and now it's been a few months, and there is no leakage. Really good, the service attitude is very good, it is really worth recommending to you, I hope it can help you.

If the ground is repaired, it is best to repair a slightly larger area, the ground should be cleaned, and the waterproof paint should be repeated 2 to 3 times.

If it is around the floor drain, the gap around the floor drain should be sealed with a leak plugging treasure or polyurethane sealing paste, and then the coating waterproof layer should be made around the floor drain

It is best to remove them all, redo the inlet and drain pipes, and test the pressure of the water pipes, and then use waterproof materials to make a waterproof layer, and the wall should be more than a meter, and the water test (put water in) to ensure that there is no leakage before the next step. You must be very serious, and if you don't do it well, you don't do it in vain.

1. Use some special waterproof glue, 2. Knock off the surface layer of the leakage, and use cement waterproof mortar for waterproof treatment, but the amount of work is still not small for individuals.

3. Find a professional company.

Tool Preparation:

Shovel, brush, rubber gloves, bucket (25L), brick-free waterproofing agent.

How to use: Use a shovel and a brush to clean the dirt at the corners and crevices;

Plugging the floor drain, there is no open water on the working face;

Add 16-18 kg of water to the main ingredient A1 of this product, stir until dissolved (note: use clean tap water with a water temperature of 18 2, and prohibit warm water or hot water mixing), subject to the fact that no particles can be observed by the naked eye;

Wait for A1 to be mixed evenly with water, add A2 material and stir well;

Add an appropriate amount of group B curing agent and stir well for 30 seconds;

The depth of the plugging liquid is not less than 5mm, and the broom is continuously swept from low to high (once every 10 minutes) to facilitate its infiltration;

It is forbidden to stir or add water and other substances to it during the static crystallization time, so as not to affect its own molecular structure and permeation effect. Depending on the room temperature, the crystallization time varies slightly;

After the crystallization is completed, the cleaning work can be carried out, the residue on the surface layer can be cleaned up, and a small amount of the remaining part can be opened and cleaned with water;

After the cleaning is completed, the floor drain can be plugged again and the 24-hour water storage test can be carried out.

The methods of waterproof leakage repair in the bathroom are: waterproof layer leakage, replacement of upper and lower water pipes, replacement of ceilings, replacement of ground water pipes, and anti-shooting and water leakage repair in the gaps of bathroom tiles.

1. Fill the leakage of the waterproof layer

If the waterproof layer is leaking, the original tile should be knocked off for base cleaning, and then the cement mortar should be adjusted and applied to the ground for waterproofing. However, the height of the waterproof wall should be controlled at about 30 cm, and the dust can be too high or too low, so as not to affect the waterproof effect.

2. Replace the upper and lower water pipes

If the upper and lower pipes are leaking and the pipes are underground, remove the tiles to repair or replace the leaking pipes. If it is a leak in the sewer pipe, it is necessary to find the specific location of the leakage, and then determine the scope of the brick knocking according to the situation, and it is not necessary to knock all of them open.

3. Replace the ceiling

The environment of the bathroom is relatively humid, and the ceiling is often surrounded by water vapor, so when repairing, it is necessary to consider replacing the ceiling with a waterproof PVC gusset, and then install it on the keel to cover the pipe, so that it can not only look good but also play a moisture-proof effect.

4. Replace the ground water pipe

If the water pipe on the ground is leaking, the floor tiles should be cut open first, and then the leaking location of the water pipe should be found, and then sealed. If there is a crack in the water pipe itself, the water pipe should be replaced, and after treatment, the water pipe should be buried again, the waterproof layer in the area should be repaired, and the floor tiles should be restored.

5. Make waterproof leakage patches for bathroom tile gaps

At this time, we don't need to repair the waterproofing of the bathroom, we only need to do the waterproofing of the bathroom gaps. Like the common ones, we can directly buy waterproof adhesive to paint the gaps of the tiles, or re-seam the gaps of the bathroom tiles, which can achieve the effect of plugging leaks.