How to install the water supply and drainage of a wall hung toilet?

The first step in hanging toilet installation is to determine the height of the water tank.

There are two types of hanging toilets: one is a top-press tank hanging toilet and the other is a side-press tank hanging toilet.

Top-press type water tank hanging toilet: the height of the water tank is adjusted from the top of the bracket to the bottom of the bracket according to the thickness of the decorative layer or wall A cm, and the overall height of the foot is 82 cm A cm. The bracket adjustment leg is only allowed to be adjusted up to 20 cm without being particularly lengthened.

Side-press type water tank hanging toilet: The height of the water tank is adjusted according to the thickness of the decorative layer A cm, and the height of the adjustable foot from the horizontal line in the white box on the upper part of the stand to the bottom of the bracket is 100 cm A cm.

Hanging toilet installation step 2: water tank bracket connection.

The installation of the water tank bracket is mainly fixed by 4 screws, two on the upper part of the bracket and two on the support feet; At the same time, all screws on the water tank bracket must be tightened. (When installing, use a spirit level to test whether the tank bracket is installed horizontally).

Hanging toilet installation step 3: connect the water pipe.

The water inlet of the water tank should be connected with the water supply pipe (hard pipe) of the water tank and the water inlet angle valve.

Hanging toilet installation Step 4: Drain installation.

If a concealed water tank is installed in the original pit, the short pipe connecting the water tank and the drainage pipe must be larger than 90 to prevent blockage.

Hanging toilet installation step 5: false wall and protective parts installation.

All protective devices should be installed before the false wall is made and the decorative layer is installed. Install the screw protection hose, divide it into two parts, and put it on the front and rear ends of the screw respectively, so as to avoid blocking the screw hole when building false walls or installing decorative layers. The surface of the light steel keel and the water tank bracket must be flat, and the position of the water tank protection frame, flush pipe, drainage pipe and screw rod shall be reserved on the gypsum board, and the gypsum board surface shall be close to the surface of the bracket and fixed.

The water tank bracket is filled with bricks or concrete below the elbow of the toilet to avoid the breakage of the decorative material caused by the gypsum board not fitting snugly to the bracket.

Hanging toilet installation step 6: red brick fixed bracket.

Seal red bricks on the edge and void of the water tank bracket, build a red brick wall of about 50 mm in front of the water tank, and reserve the position of the water tank protection frame, flush pipe, drainage pipe and screw. The minimum thickness of red bricks is about 50 mm.

Hanging Toilet Installation Step 7: Install the toilet.

After the false wall is decorated and the tiles have been pasted, the soundproof mat is attached to the decorative wall, the pipes are measured and cut, and then the toilet is installed according to the position of the screw, the length of the screw exceeds the ceramic surface, and the toilet is fixed to the wall. When installing a wall-mounted toilet, pay attention to adjusting the horizontal position of the toilet, and cut off the excess soundproof mat after the installation is completed.

1. Before installation, check whether the sewage pipeline is unobstructed and the installation ground is clean.

2. Install the matching sealing ring on the sewage outlet of the toilet.

3. Determine the installation position of the toilet. Align the toilet drain with the pipe drain and slowly lower it, adjust the correct position, and then use chalk or whiteboard markers to mark the line around the toilet and determine the installation holes.

4. Punch installation holes. Align the anchor screwing marking hole, use a percussion drill to punch the mounting hole, the diameter is 10mm, the depth is 60mm, and the expansion glue nail is loaded, and the anchor screw is generally not installed.

5. Label the inside of the marking line with glass glue.

6. Align the installation hole and the surrounding glass glue to install the toilet, and slowly press down until it is horizontal.

7. Put glass glue on the connection between the toilet and the ground, and trim the surrounding area to ensure the appearance.

8. Install the anchor wire.

9. Connect the water inlet pipe and check whether the filter is installed.

10. Clean the ground and tools, and prohibit immediate use. Because it usually takes 24 quarters of an hour for the glass glue to cure, it is necessary to keep the area around the toilet free of water for 24 quarters of an hour.

Press the interface of the toilet to deal with it?